Jump to content

Imperial91

Member
  • Content count

    46
  • Joined

  • Last visited

Everything posted by Imperial91

  1. Not my truck, a buddy of mine at a car show. Paint matched looks better than chrome! Sent from my iPhone using Tapatalk
  2. I run 20x10 -25 offset with 33x12.5 Atturo Trail Blades XT. However, I also have 3" lift spindles and Bilsteins on the max setting up front. Without having spacers in the rear yet, you can see the difference in track width. Before the spindles I rubbed a lot. After the spindles less rubbing. You can get by... I would suggest a minor NorCal mod. Sent from my iPhone using Tapatalk
  3. I don't have the Corsa setup on mine. The tips however are similar, I have them going out to both sides of the truck, with a Carven muffler. I love the way it sounds. Sent from my iPhone using Tapatalk
  4. Guys I made a mistake and over torqued the front lower strut bolts. I over did it with the impact to be more specific haha. One of them is right and not moving at all the other. The tabs broke off and is just hanging there loose. Now I don't even know what these tabs are called to even look for them? Should I just replace them with a bolt and washer/nut? Sent from my iPhone using Tapatalk
  5. Yesterday I added 3" lift spindles to my already bilstein 5100's on the top setting. I drove around hauling an invisible trailer and got an alignment. The ride itself is actually not bad. It's firm, but it's a nice firm. Today I replace stock blocks with blocks to raise the rear 2 inches. I haven't measured it yet, but the stance looks a lot better than before. Sent from my iPhone using Tapatalk
  6. I had a shop install them the first time around. Thanks for the input. Sent from my iPhone using Tapatalk
  7. Yeah I feel like the ride improved up front. It makes a difference between the front and the rears. I need to upgrade my rears still. Sent from my iPhone using Tapatalk
  8. This is my truck stock with only the 5100's added to the front on the highest setting. I've only had it on the highest setting, so I don't know about the others.. Sent from my iPhone using Tapatalk
  9. I watched a video on YouTube about using carnauba wax on painted wheels to keep a layer of wax over them helping to keep them clean and protected. Look up 'Wheel shine daddy' a video by Custom Offsets. Sent from my iPhone using Tapatalk
  10. I'm almost thinking if I would have went with a 3 inch level they might clear. Sent from my iPhone using Tapatalk
  11. Not my picture but it rubs right here... it's right before full lock, the edge of the tread brushes against the felt. There is also a small bolt there holding the factory plastic moldings it rubs one while passing by it. In this picture the person did a little trimming there Sent from my iPhone using Tapatalk
  12. Out with the old... In with the new! 20x10 Full Throttle -24 offset 33x12.5x20 Atturo Trail Blade XT 5100's on top setting in the front. Rubbing rear end of fender well. Not too bad. Debating about going higher or getting slightly smaller tires. Sent from my iPhone using Tapatalk
  13. GM CK948 wheels you can find them online... pretty pricey from GM. I bought them used from someone locally. Sorry for the late reply. Sent from my iPhone using Tapatalk
  14. Well damn. That looks nice haha. It looks a little funky with the 33's. if I lower I don't know if I will keep same wheels and go with different tire or switch wheels to maybe some 22's. The current wheels are 20's. Sent from my iPhone using Tapatalk
  15. Washed it the other day. Sometimes I think about changing the wheel/tire setup and lowering the stance but pics like this change my mind haha! Sent from my iPhone using Tapatalk
  16. Installed a Carven muffler to y-pipe with dual wall tips to each side. Don't have a video yet, but I love the way it sounds! Sent from my iPhone using Tapatalk
  17. Seems a bit much, but if it looks as good as that it may be worth it. Sent from my iPhone using Tapatalk
  18. Anyone have an idea of how much a full wrap like that would cost? Sent from my iPhone using Tapatalk
  19. I am running a similar setup, except with 33x12.5x20 Toyo M/T's. Sent from my iPhone using Tapatalk
  20. To add to my previous message, I replaced my stocks with new wheels and tires. One of my original sensors was not working after install. I ended up taking it to Firestone. $20 later and a flash of wand, essentially, it worked. Sent from my iPhone using Tapatalk
  21. I think they need to be activated. Sent from my iPhone using Tapatalk
  22. Off-roading accident? Where in Arizona do you off-road, and how intense is the ride? Sent from my iPhone using Tapatalk
  23. That thing is gorgeous! Sent from my iPhone using Tapatalk
  24. From what I was reading it has less to do with speed and more to do with torque. So I guess even at slow speeds the front end is naturally torqued downward while in reverse. I guess that makes sense. Sent from my iPhone using Tapatalk
×

Important Information

By using this site, you agree to our Terms of Use.