Jump to content

jbh4381

Member
  • Content count

    36
  • Joined

  • Last visited

Community Reputation

12 Good

About jbh4381

  • Rank
    Enthusiast

Profile Information

  • Gender
    Male
  1. Mine was $779.88 shipped to my door. I used https://www.tonneaufactoryoutlet.com Deals are out there, you should be able to get one delivered for less than $800. Online chatting or calling in will almost always guarantee a lower price. Sent from my iPhone using Tapatalk Pro
  2. Yes. I’m 290, give or take depending on if I’ve eaten or not. Haha. Sent from my iPhone using Tapatalk Pro
  3. MX4 is solid, someone would really have to want your stuff to break into it. It was 99% waterproof also, very rarely did water get in. Do a good job on the seals and alignment and you won’t have issues. I’m also a big guy and would sit on top of mine with no issues. Very sturdy cover. Sent from my iPhone using Tapatalk Pro
  4. I had that on my CC for a year. I didn’t have any issues with the cover, but it was a pain when I wanted to haul my bikes. I just put the Revolver on instead, MX4 is in the garage. Not a bad cover at all. Sent from my iPhone using Tapatalk Pro
  5. This is a 285/65 18 on the Z71 wheel. I am running a 2.5 level on the front. I have the BFG KO2 tires, they are 32.6” i believe. Sent from my iPhone using Tapatalk Pro
  6. Just shot an email over. Really liking this upgrade, looks awesome. Sent from my iPhone using Tapatalk Pro
  7. I believe it had the USB receptacle on one side, and a pin connector on the other. I’d snap a picture of it, but it is in my attic inside of the jump seat. I bought the cable that is from GM to run USB from the glovebox to the triple (from what understood) but it wouldn’t power with just a USB. I’m sure that is where splicing comes into play, but I didn’t feel comfortable with that part of it, so I went the route of having just 12v and 110v up front. Sent from my iPhone using Tapatalk Pro
  8. I read it but didn’t comprehend it to the point that I felt comfortable. I found the plate from 2014 that didn’t have the USB and went that route. A little bummed but I didn’t have the USB before with a jump-seat, and I still have my console USB and Glovebox USB if needed. My 12v skills are novice with the new vehicles, haha. Sent from my iPhone using Tapatalk Pro
  9. I took the harness from my jump seat and used it to make connections. It wasn’t tough, anyone with basic 12 volt skills can knock it out. The only splice I had to do was for the console light. Everything else hooked up. I couldn’t get the front 3 USB to work so I did buy a plate for the front that only has 2 12v and 110v outlets. Sent from my iPhone using Tapatalk Pro
  10. I ordered a console for a 2015 Silverado and I have a 2016. It was about $100 cheaper at the time. I don’t have the wireless charging lid (wish I did), but my cup holders are removable (don’t think they are on the 2016-newer models). You’ll be fine with any console from 2014-on. Sent from my iPhone using Tapatalk Pro
  11. It isn’t tough, just take your time and you’ll be good. Sent from my iPhone using Tapatalk Pro
  12. I had mine done by a shop. They quoted me 1.5 hours of labor. With the alignment and 7% tax, I was at $266 OTD.
  13. Tampa Florida. The last couple weeks have been terrible if you have to work outside. I typically am able to handle it but will be glad when it's over this year. Sent from my iPhone using Tapatalk Pro
  14. Gotcha. None the less, I am going to keep brainstorming on it until I get a solution that works. Hopefully the summer heat will die down soon and it'll actually be bearable to work outside. Sent from my iPhone using Tapatalk Pro
  15. I do, didn't think it would fit. I'll look at it tonight. Man that would be cool if it works. Sent from my iPhone using Tapatalk Pro
×

Important Information

By using this site, you agree to our Terms of Use.