Jump to content

2014 Differential Fluid Change


Recommended Posts

Just came in from changing the fluid in the differential. Looks like there was only about 2 quarts in the diff. I added 3 back to the diff and it just started to seep out the fill hole. is this still the acceptable level for these diffs? Its always been that way when I done the drain and fill on different vehicles in the past. I took it down the road after the fluid swap and it seems to be a little more quite and smoother. There was no signs of leakage anywhere near the diff.

 

Differential%20Fluid_zpshx0ltffn.jpg

Link to comment
Share on other sites

  • Replies 38
  • Created
  • Last Reply

Nice.

 

How many miles is on the truck? I try to get my differential fluids changed out early. Usually around 5k miles on the vehicle. That way I get all the wear-in material out of the differential and clean up the magnet. Then the fluid is good to go for 100k unless you do a lot of towing/hauling then I would change out at 50k miles.

 

Most do not change it out and never have a problem. I just feel better and it is something that is really easy to do.

 

Thanks for the tip on finding out what size differential you have.

Link to comment
Share on other sites

You need to find out if the "seep out the fill" is the correct level...some it is, some want it below the fill hole.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

 

You are correct. It's not difficult to drain with the transfer pump. Just pull a little out and be done with it.

Link to comment
Share on other sites

 

You are correct. It's not difficult to drain with the transfer pump. Just pull a little out and be done with it.

 

Santa is bringing me a PML diff cover for Christmas! PML says it has approximately .6 quarts over stock capacity. So how much should I fill it up with this new diff cover? Should I just fill it until it starts to run out the fill hole or how much under the fill hole?

Link to comment
Share on other sites

Santa is bringing me a PML diff cover for Christmas! PML says it has approximately .6 quarts over stock capacity. So how much should I fill it up with this new diff cover? Should I just fill it until it starts to run out the fill hole or how much under the fill hole?

 

I never found a definite answer to the question other than, 2.75 quarts for the 9.5 diff. I filled it up till it seeped out the hole which was right at 3 quarts. If you look at my pics, I only took out just a tick over 2 quarts. The full bottle is 60 ounces. The small one i am guessing is 4 ounces of fluid.

Link to comment
Share on other sites

Santa is bringing me a PML diff cover for Christmas! PML says it has approximately .6 quarts over stock capacity. So how much should I fill it up with this new diff cover? Should I just fill it until it starts to run out the fill hole or how much under the fill hole?

Compare the old cover with the new one...the one ORU cover I ran had the fill hole almost 2 inches higher than OE...that's how they get so much more "capacity".

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

Link to comment
Share on other sites

Compare the old cover with the new one...the one ORU cover I ran had the fill hole almost 2 inches higher than OE...that's how they get so much more "capacity".

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

No this one actually has more space/capacity, for example you would need this cover if you were swapping to 4.10 gears to provide clearance for the larger ring gear.

 

I think I'll just email PML and see what they say.

Link to comment
Share on other sites

 

I never found a definite answer to the question other than, 2.75 quarts for the 9.5 diff. I filled it up till it seeped out the hole which was right at 3 quarts. If you look at my pics, I only took out just a tick over 2 quarts. The full bottle is 60 ounces. The small one i am guessing is 4 ounces of fluid.

Yea, sounds to me like the OEM was under filled in my opinion.

 

I'm one of those guys who would rather have a little more than a little less. If that's bad or not I don't know. As for the rear diff I don't see how a little more could cause a problem as it would just come out the vent.

Link to comment
Share on other sites

No this one actually has more space/capacity, for example you would need this cover if you were swapping to 4.10 gears to provide clearance for the larger ring gear.

 

I think I'll just email PML and see what they say.

Why would you need more room for 4.10s? The ring stays the same size regardless of gear set (in the same differential)...the pinion is a fixed point.

 

I didn't say that was the way your cover made that difference, only that some do and it's worth checking.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

Link to comment
Share on other sites

Why would you need more room for 4.10s? The ring stays the same size regardless of gear set (in the same differential)...the pinion is a fixed point.

 

I didn't say that was the way your cover made that difference, only that some do and it's worth checking.

 

Sent from my SAMSUNG-SM-G900A using Tapatalk

 

2014 Silverado 1500 with Aftermarket Gears

 

Yukon Gear tested this PML cover with their 9.5 Duragrip aftermarket carrier. The stock cover requires a spacer or modification because of clearance issues with aftermarket carriers, such as Duragrip. Aftermarket carriers are required when changing to 4.10 or deeper aftermarket gears. The PML cover does not need a spacer. This will benefit customers doing the following:

 

Adding an aftermarket limited slip carrier to stock gears

Changing gear ratios and using an aftermarket carrier

 

Read here for more information if you're curious...

 

http://www.yourcovers.com/diffcover_11129.php

Link to comment
Share on other sites

2014 Silverado 1500 with Aftermarket Gears

 

Yukon Gear tested this PML cover with their 9.5 Duragrip aftermarket carrier. The stock cover requires a spacer or modification because of clearance issues with aftermarket carriers, such as Duragrip. Aftermarket carriers are required when changing to 4.10 or deeper aftermarket gears. The PML cover does not need a spacer. This will benefit customers doing the following:

 

Adding an aftermarket limited slip carrier to stock gears

Changing gear ratios and using an aftermarket carrier

 

Read here for more information if you're curious...

 

http://www.yourcovers.com/diffcover_11129.php

That's another reason not to own a 1500...

 

Sent from my SM-T350 using Tapatalk

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    245.8k
    Total Topics
    2.6m
    Total Posts
  • Member Statistics

    333,235
    Total Members
    8,960
    Most Online
    fasal a
    Newest Member
    fasal a
    Joined
  • Who's Online   2 Members, 0 Anonymous, 655 Guests (See full list)




×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.