Jump to content

GM-Tech

Member
  • Posts

    3,297
  • Joined

  • Last visited

Contact Methods

  • Website URL
    http://

Profile Information

  • Location
    South Florida

Recent Profile Visitors

4,580 profile views

GM-Tech's Achievements

Senior Enthusiast

Senior Enthusiast (11/11)

1

Reputation

  1. There's actually some logic in the P0116 DTC test that tries to determine if a block heater has been used. On the other hand, this is a type B code, which means the DTC test has to fail on two consecutive ignition cycles (in which the test runs) for it to turn the light on. So you're not in the clear yet on the light not coming on.
  2. The code does not disable your temp gauge. Something unrelated is wrong there. Also, your engine should not run any differently.
  3. Instead of all this darn moanin' and groanin', just cut the d**n plug off and put a standard three prong plug on it and be done with it. If the SES light comes on, deal with it by leaving it on or have it checked and cleared every time.
  4. Actually, we're already beggin' the newcomers to go back. The place is overflowing with people, growth is out of hand, my $135,000 house purchased 10 years ago would now cost me a half-million, and trust me, it's not what I would think of as a half-million dollar home. Roads are crammed like never before. Thank goodness I'm only a few miles from work and the opposite way traffic flows in the morning and night.
  5. Oh yeah, that'll have GM shivering in their boots... oh wait, maybe it's YOU that's shivering in your boots! I have the solution. Move down here where I'm at. It was 80 degrees today.
  6. Chances are zero to none. This coolant temp rise test is a federal emission requirement. Talk to your legislators and see if you can get them to convince the EPA that you would like to have your truck warm when you start it up. GM has little say in this stuff. They have to certify the vehicle with the EPA and can't just change calibrations willy nilly. Any change that would affect emissions would have to go through the same certification process.
  7. Yeah, it is a bigger deal than you realize. This is not GM's decision. They have to meet certain standards that define what tests are run, when, and what the results must be to be in compliance. They can't just tweak things to suit their (or your) needs. As for your question as to whether or not the light will come on.... yes, after the second consecutive failure. Here's the full details on the criteria that must be met for DTC P0116 to run and what happens if it fails. This test appears to be able to detect if a block heater is in use, in which case the test aborts, but perhaps under some conditions, it may fail the test anyway. --------- Conditions for Running the DTC • The ignition is ON. • DTCs P0112, P0113, P0116, P0117, P0118, P0128, P0502, P0503 are not set. • The start-up IAT is more than -7°C (+20°F). • The vehicle has a minimum ignition OFF time of 10 hours. • DTC P0116 runs once per drive cycle when the above conditions are met. Conditions for Setting the DTC • The start-up ECT is more than the start-up IAT by 100°C (180°F). OR • The start-up ECT is more than the start-up IAT by 15°C (27°F), then the vehicle must be driven for more than 400 seconds over 24 km/h (15 mph). If the IAT sensor temperature decreases more than 8°C (14°F), a block heater is detected and the test is aborted. If the IAT sensor temperature does not decrease, a block heater was not detected and DTC P0116 sets. Action Taken When the DTC Sets The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. Conditions for Clearing the MIL/DTC • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. • A current DTC, Last Test Failed, clears when the diagnostic runs and passes. • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. • Clear the MIL and the DTC with a scan tool.
  8. Oh, there's someone at GM that knows the answer. It's just finding him or her. As for getting different answers based on the person contacted... is it really any different anywhere else? I don't think so. I've called on various topics from insurance problems (darn hurricanes) to tech licensing in Dade county. I get a different answer every time I've called! That's not to say that it shouldn't be that way.
  9. I wouldn't rely on what one guy at Partech says anymore than I'd rely on what one of the guys at TAC says. I can talk to 3 different guys at TAC and get three different answers. It's really frustrating at times. Some of them are pretty sharp, others know little to nothing.
  10. I agree that the possibly damage theory doesn't make sense. Like you said, it runs hotter than that under normal conditions. I'm sure there's some reason for it. Finding the guy that knows the answer might be difficult.
  • Forum Statistics

    245.7k
    Total Topics
    2.6m
    Total Posts
  • Member Statistics

    333,066
    Total Members
    8,960
    Most Online
    Wicked Mayhem
    Newest Member
    Wicked Mayhem
    Joined
  • Who's Online   1 Member, 0 Anonymous, 569 Guests (See full list)

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.