Jump to content

A.J. Curtis

Lifetime Supporting Member
  • Posts

    536
  • Joined

  • Last visited

  • Days Won

    1

A.J. Curtis last won the day on December 18 2016

A.J. Curtis had the most liked content!

1 Follower

About A.J. Curtis

  • Birthday 10/18/1978

Contact Methods

Profile Information

  • Name
    AJ
  • Location
    Norcal
  • Gender
    Male
  • Drives
    2015 Chevy Silverado 1500 LT 4wd

Recent Profile Visitors

8,413 profile views

A.J. Curtis's Achievements

Enthusiast

Enthusiast (6/11)

246

Reputation

  1. Yes they are OEM LTZ headlights. I will check the breather valves! They seem to be okay for the moment.
  2. You are a flipping genius!!! I purchased the headlight used off of another member who drilled the holes in the dust caps. They were completely off for the use with the FX-r projectors. Once I dremel’d out the opening more the headlights aligned perfectly. Any ideas on what to check for moisture getting in where the high beam and turn signals are? While I had the lights off the truck I used a air dryer to get rid of the water and then checked every bulb and gasket on the dust covers. Sent from my iPhone using Tapatalk Pro
  3. It handled an iPhone7 pretty good! There is no real support there but it held okay. When I moved it to the cd slot I noticed some slight warping of the plastic from it. It eventually went back to normal. I’m sure if something that weighs more would hold though. Sent from my iPhone using Tapatalk Pro
  4. Thank you for the suggestion! I will see if that works.
  5. Update! Everything is working flawlessly now! I have one little issue though. My passenger side head light adjuster is maxed out all the way and I can't get the beam any lower. I have FX-r projecters installed in OEM LTZ projector headlights using the Fastheadlights adapters. Does anyone have a suggestion to lower the beam?
  6. I don’t think so but I will look closer. I truly appreciate the help! Sent from my iPhone using Tapatalk Pro
  7. I checked the capacitor and it looks correct. Is it possible the capacitor went bad the same moment I swapped the bulbs? I will swap it this weekend and see if that makes a difference. I just don’t understand why it would stop working. You are right everything works fine except for the DRL/running lights Sent from my iPhone using Tapatalk Pro
  8. That sounds like it is the solution! I will check when I get home. Thank you so much for the help!
  9. Thank you for the response! Yes I only have one capacitor link on the passenger side per the Morimoto instructions as it is on the side closest to the battery. Do I need one on the drivers side? I wired it up per the picture. The Morimoto kit that I have doesn’t use the standard D2S bulb with the large D2S igniters. It uses the D2H bulbs which I think uses a 9006 connector? Sent from my iPhone using Tapatalk Pro
  10. I have had the orginal OPT7 redline on for 3 years and not a single issue. I picked it up on amazon for $60 and it is super bright. I wish the Putco blade was half the price cuz I'd love to rock that one.
  11. Hey everyone, I need a little help. I've had a Morimoto Elite HID kit for my low beams the last two year. One of my bulbs went out & I decided to finally install My FX-R Projector retrofit kit from fastheadlights. I used the same existing morimoto HID kit that was already installed and working. I swapped the "bulb Wires" that plug into the "Amp Igniters" and left everything else the same. I lost my DRL/running lights and auto on Both the driver and passenger side headlight turn on and works with all running lights if I have the head light switch turned all the way to ON, other than that I get nothing. I triple checked every connector and they are all firmly connected with a positive "click" sound too. Any suggestions on what to check would be greatly appreciated!
  12. Damn! Thank you for responding! I am all the way out on California and need me a bumper too.
  13. Where are you located? Sent from my iPhone using Tapatalk Pro
  14. I did install them and had them on for a few months. I really liked them but a lot of the black on the truck was flat so I took them off. I still have them and have been thinking about plasti diping them or getting them LineX'd. The install on the rears are easy but you have to use self tapping screws on the front flares.
  • Forum Statistics

    245.8k
    Total Topics
    2.6m
    Total Posts
  • Member Statistics

    333,235
    Total Members
    8,960
    Most Online
    fasal a
    Newest Member
    fasal a
    Joined
  • Who's Online   1 Member, 0 Anonymous, 657 Guests (See full list)

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.