Tyy1907
Member-
Posts
113 -
Joined
-
Last visited
Profile Information
-
Name
Tyler
-
Drives
2018 Silverado 1500 LT Z71 4x4 6 speed
Recent Profile Visitors
2,652 profile views
Tyy1907's Achievements
Enthusiast (4/11)
15
Reputation
-
Rear defrost not working
Tyy1907 replied to Tyy1907's topic in 2014-2018 Silverado & Sierra Troubleshooting
According to that document I "should" replace the whole assembly. I'm off warranty so no thanks I resoldered the loose lower tabs back on. I've got 14 volts at the drivers side portion of the window. Nothing on slider or passenger portion. There's an electrical connection that connects to that drivers side window (I pulled off pillar panel to see it) but I can't figure for the life of me how that drivers part connects electrically to that middle or pass side. Funny thing is I have 6 - 8 ohms from slider to drivers side when defroster is off. Gonna tear open under pass side tomorrow -
Rear defrost not working
Tyy1907 replied to Tyy1907's topic in 2014-2018 Silverado & Sierra Troubleshooting
I found that plastic cover that covers the contacts was melted a little. Pulled it off and the lower contact tabs (ground?) were dislodged. Bought the conductive epoxy kit and reattached and still doesn't defrost a thing. Fuse continuity is good, tested relay with 9v battery as well. I've got no voltage going to the grid at all. Continuity of the grid is good -
Tyy1907 started following Fuse box fire , Rear defrost not working and Oil pressure issue
-
The side mirrors seem to defrost but definitely not the rear window or slider. Tried to clean electrical tabs for slider window, see if that did something. Fuse is still good
-
Good luck Mine just did this code ND dealer found shavings in my oil pan. New engine time. 154,000 km
-
Yikes. Was something jumpered?
-
Pics of leveling kits with stock wheels
Tyy1907 replied to Gingerly's topic in 2014 - 2019 Silverado & Sierra
Ive got a white 18 Lt but crew cab standard box. This is the identical setup I'm looking to get. Got the stock 18's as well. Ive got airbags in the back though as I carry a truck camper. Looks good! Is yours a lower spacer or an upper? -
Leveling With Stamped Steel Upper Control Arms
Tyy1907 replied to reardiff's topic in 2014 - 2019 Silverado & Sierra
So for anyone that can comprehend that gobli gook, ive got an 18 Lt with a steel knuckle. Found Craigslist Cast steel uppers off of a 14. Would these balljoints fit in my knuckles? -
But do they need to document it was done and what not? Maybe your dealer trusts you Heck I'll donit myself too it's such a PITA taking it in to dealer
-
Itll just destroy one of your rear window segments. Some trim will melt also F150s have had this problem longer than chevys from what I've gathered and they've issued no recall so +1 for gm. I e looked on some f150 forums and it seems to ne that debris caught in the sliding window or something else bends one of the contact tabs basically arcing across the larger gap and causing big time heat resulting in melted window trim and eventual glass smashery.That's my current conclusion which is subject to change. I was called to bring in my 2018 Lt so they could pull the defrost fuse. If I can adequately see the contacts and periodically inspect them I might just put the fuse back in as I use my rear defroster dammit! We have cold temps up here.
-
Rough Country 3.5" Knuckle Lift
Tyy1907 replied to rastasquid's topic in 2014-2018 Silverado & Sierra Mods
Angles are not near stock. I thought they'd correct the angles more considering they're throwing in new knuckles too but they tilt the upper balljoint mount so it's more in a level plane putting less stress on the balljoint but other than that the tie rod angles are steep and CV angles are equivalent to a 2.5" level. -
Aftermarket backup cam, Oem screen as display
Tyy1907 replied to Tyy1907's topic in 2014-2018 Silverado & Sierra Mods
-So the black wire that says yellow end is an rca cable and has a red a yellow and a bare ground in it -This red wire runs from where it says "to reverse light" all the way to where it juts out near the bottom. Continuity the whole way Yellow and ground run from camera to "yellow end" ( ground splits off also as seen) -
In my quest to restore and use a truck camper I bought on the cheap I need to install a different backup cam as my tailgate needs to be down or removed. K no big deal but I'm looking into trying to plug an aftermarket cam into my 8 pin plug that the oem plugs into so I can use my factory screen. I've been doing quite a bit of research on this and found some good wiring diagrams thanks to this forum. And found a source for the plug and pins. However I cant quite nail down what wires should go where. Any help would be great
-
I just ordered an auto vox 6 license plate cam for when my truck camper is on (tail gate has to be down/removed). I've also ordered the compatible plug and pins that plug in where my tailgate camera plugs. Am I dreaming or does think this will work?
-
Superlift 3.5 Pics and opinions
Tyy1907 replied to contenderv07's topic in 2014-2018 Silverado & Sierra Mods
Anyone try 4 hi at 60 mph Still smooth as factory?
-
Forum Statistics
246k
Total Topics2.6m
Total Posts -
Member Statistics
-
Who's Online 27 Members, 0 Anonymous, 1,908 Guests (See full list)