Search the Community
Showing results for tags 'Drive line'.
Anyone know what this noise is? It's very intermittent. Seems to do it most often between 40 and 50 MPH cruising with maybe a slight up hill. Never does it on coast or heavy acceleration. Very hard to tell where it's coming from. 20190521_191545_001.mp4 2014 Sierra Denali 1500 Crewcab, 5'8" bed 6.2 Litter 3.42 axle ratio about 118,000 miles
Trying to pull the front driveshaft on my '07 Sierra 1500 (new style). Front of shaft is free (out of front diff) but at the back end there is a pressed u-joint (no bolts) with a short rubber boot clamped over the spindle end and it is not sliding out of the transfer case as easily as other driveshafts I've pulled in the past. Dont want to force it if the boot is what's holding it back. Do not see any videos or explanatary photos online showing how the DS removes from the transfer case. Anyone help? See photo. Much thanks...
I’ve searched previous forums and haven’t found the feedback I’m looking for, although this is a common topic. So bear with me. I have a 1999 Silverado 1500... 5.3L.... 4l60e... 4WD... NP246 TC.... 3.73 gear ratio... 160k miles. The symptoms I’m having are namely: Large clunk when shifting into reverse. A less noticeable, but still at times, a clunk when shifting into Drive. Harsh down shifts when coming to a stop from cruising speeds. Today, I put the truck on 4 jack stands so I could get a better idea of what is going on. After being under the truck during shifts between Park Drive and Reverse , it seems to me the “clanking” is originating from the Transfer Case. And mainly from the output shaft that drives the front diff. When the truck is turned off and in park, I can manually with my hands rotate the front drive shaft back and forth and replicate the same (ish) banging noise I hear when making those shifts between P D and R. The noise is consistent whether the truck is in 2WD, 4 HI, or 4LO. I guess my question in general is what testing can I do to further look into this and figure out the root cause? Would these symptoms typically originate from the tcase? My long term plan is hopefully to replace both the Transfer case and front diff with either low mile junk yard OR remanufactured units. after replacing those things, assuming a good install, do you believe the “clanking” will be fixed? In general, the truck is shifting through gears like dog ******. But I love her and want to renew it over time.
Hi Everyone, So my truck has been at the dealership two times officially now. This 3rd time I had my friend look over it and he said the truck was within GM's specs. I don't know what GM's specs for vibration are but my vibration is in the mid 70mph range and excessively vibrates and then smooths out. This is a constant cycle throughout my commute. I am going to pull my driveshaft and take it to a shop that specializes in driveshafts. I know several people have had their driveshafts replaced under warranty and it did not correct the issue. My thoughts are if your truck originally came with an out of spec driveshaft chances are there is a whole stockroom somewhere in the Parts Department that has out of spec driveshafts mixed in with the ones without issue, hence the reason some people have no luck with driveshaft replacement. I really feel this could be one of the major issues behind all of this especially when there is documentation instructing the technicians at the dealerships to use hose clamps to balance the driveshaft. I'm sorry but I don't see hose clamps as a permanent correction to this issue. I will update this post when I get the results from the driveshaft inspection. Please feel free to share your thoughts and bounce ideas around. Collectively I believe we can find an aftermarket fix for this issue, it may not 100% resolve the issue but will at least save people from taking huge losses on trade in (if you did not go through a buyback/lemon/customer satisfaction program). (A lot of people are trading in / selling their trucks because of this issue) ***UPDATE 01-22-2016*** I contacted the Team at Precision Shaft Technologies (http://pstds.com/) in Clearwater FL and they were able to squeeze me in as a walk in. (Not there normal protocol. They were super friendly, informative, and VERY helpful!) I drove up there and pulled the driveshaft in their parking lot. They then put the driveshaft on a machine and it was a near perfect balance. They added one small shim to the U joint to get it perfect but I'm sad to say the vibration is still present and there was no change. However, when I returned home I put my truck up on jack stands and ran it up to the speed I had issues at (per GM's service docs) and there was NO vibration. I was extremely confused at this point. I dumbed it down and looked at the rear wheels while the truck was in drive (idle speed) on the jack stands (be sure to block your front wheels and disable traction control / StabiliTrak if you plan on doing this on your own). I noticed my left rear wheel has a slight flat spot it in so much so that it's extremely difficult to notice. I have not had a chance to swap a known acceptable wheel to the rear at this time. When I do I will update this post. A recap for a description of my vibration: -72-74 MPH there is a cyclic vibration. Roughly every 7-8 seconds the truck has a vibration and then the vibration disappears.