Search the Community
Showing results for tags 'door'.
-
Hi all, my 2016 1500 chevy silverado lt had 3 door lock actuators were inoperable or making noise. Common issue,ordered 4 new lock acuators from Gruven parts and put 3 in. They work great but noticed drivers door when opening or closing will not turn on or turn off interior lights and also radio stays on when closing door. Sounds like a bad door switch to me which is in the latch I believe. Thinking I caused the problem since it worked fine before. Went back in the latch and all looks fine. Was hoping to see a gear out of place or something, but looks ok. Anyone have some insight on this. Maybe a door schematic you can share to check the wiring. Thank you in advance
-
I have a 2010 silverado 2500hd. I am having an issue with the driver door lock, all the other doors lock and unlock just fine. I found a broken wire in the rubber boot between the door and the cab and fix it accordingly. I looked up what fuses if would be and i replaced those, all was well for about a week then I pulled the panel off and put new speakers in and tightened the metal plate behind the door panel. Then it just stopped again. So I pulled the door panel off again and found the wire i had previously fixed was broken again so I pulled the entire harness and soldered the wire. Put everything back together with no luck. Now, the BCM doesnt even recognize the door being open or closed (courtesy lights no longer come on when I open the door.) I bought a new actuator thinking that was the issue plugged it up to test before removing the old one, still no luck. I used a DMM to test for voltage at the connector to the actuator and the connector that goes to the switch. I have a constant 11.4 volts at the switch and at the actuator connector. However, when I push the lock button, the voltage drops anywhere from 1volt to a 11volts. When press the unlock switch the voltage drops maybe a half volt. I was told that the switch is grounding out some where, but i have no idea where that would be, all the wires in the harness appear to be in good condition, I tested the ohms in the harness and everything checks out, no broken wires. I was thinking that maybe the relays in the I/P junction box are going bad, but i really dont know. I can lock and unlock all the doors from the driver switch except the driver door. Doesnt work with the remote either. Does anyone know where or what else I should check? Anyone else ever have this issue, if so, how did you resolve it? Any input or insight is greatly appreciated! Thanks.
-
- Driver door lock
- Driver
-
(and 2 more)
Tagged with:
-
I was just driving back from vacation early morning and had my arm on the window and noticed something flapping in the wind. Looked to my passenger side and nothing so then I started looking in the mirror and noticed I had a door pillar cover flapping, particularly when I'd get above 65mph. Brought it to the dealer and when I was there we realized 4 out of the 6 had this problem. Service advisor indicated this was a known issue and its a replacement part with a new design. Was under warranty so I lucked out and got free replacements. The covers are secured by a bolt at the bottom and its the middle or top that flaps. I thought I'd share as I had 4 out that I didn't realize and they must have been doing this for some time. You can easily test by just pushing on it in the middle and top and if there is any give, it probably needs to be replaced. I've seen on other forums some people use silicon to fill it if its out of warranty and it seems to hold.
- 2 replies
-
- pillar cover
- window
-
(and 1 more)
Tagged with:
-
Just an FYI for an issue I just resolved with my 2 week old 2017 Silverado. Drove off the lot and put on some music that had some mid-range bass and my passenger door speaker was causing a rattle that I wasn't sure if it was the door rattling or a blown speaker but either way it was horrible and needed attention by the dealer. Dropped it off and they pulled the interior panel and added sound proofing tape and wrapped the area they believed was causing the problem. Was in and out in a couple of hours and was covered in full by warranty. Cranking some old hip-hop without any rattle and I'm a happy camper. Dealer said this has been an issue for years and I was able to find a similar thread on a 2014 here... Easy fix...
-
I was driving through a curve while looking at a bear out my driver side window at 5 mph. The road apparently straighten out but I didn’t. I drove 2 feet off the road and drove up onto an approximately 2 foot tall boulder.... There was a smaller rock directly in front of it to guide my tire up onto it. I immediately felt my front end lifting up and I turned toward the right while applying my brakes. My truck came off the boulder and I “high centered” it on my driver side rocker panel and driver side door. Anyone have experience taking this in for repairs through insurance? The rocker panel is part of the 1 piece cab. Will they need to replace the whole cab, or are there parts they can weld in? What is the damage $? I plan on taking it to my dealership as they have a body shop. I guess I am afraid it may be totaled if it requires a whole cab replacement...
- 16 replies
-
- 1
-
- damage
- rocker panel
-
(and 2 more)
Tagged with:
-
My first post!! I purchased the OPT7 AURA Pro light kit to install on the floor board in my 2019 GMC Sierra 1500 Denali. (Hard to believe a $67,000 truck does not have lights there). Does anyone know which wire from the door that tells the dome light to come on when the door opens? Or have the wiring diagram?
-
On my 2008 GMC Sierra SLE ext. cab, my “driver door ajar” warning comes on when I put the vehicle into gear. My dome lights turn off and the doors all lock, including the driver door. Would the problem be in the driver door latch? Is there anything else that could cause this issue? Thank you.
-
- gmc sierra
- driver
-
(and 3 more)
Tagged with:
-
Well today while driving down the highway without warning my drivers side window decided to explode for no apparent reason. There was no traffic passing me or passing by in the oncoming lane. The only other vehicle was another car behind me about 75ft or so. Anyone else had this happen please share.
-
I am looking for a chrome FRONT PASSENGER side exterior door handle for a 2018 Sierra. I am looking for OEM not aftermarket. I really only need the small piece that fits the aft side of the handle so I don’t care if the grab handle part isn’t perfect. Thank you.
-
1) The instrument cluster between the tach and speedo resets along with the HUD. This happens quite often, I have owned the truck for a month now and it has done it about 50 times. I did find a service bulletin: #18-NA-324. 2) The movable air control door hidden inside the dash seems like it 'sticks' and won't position itself properly for what is asked from either the touchscreen or manual controls. For instance, when I remote start the defroster is automatically set. That works fine; but in order to get ANY flow to the floor one must first select the combo defrost/middle area to 'unstick' the door. You can literally hear the door unstick and move. You can then select to the floor for air flow and it will work. 3) On a smaller note, the right rear door does close properly; it seems like it rubs on something during the closure process; I'm sure that is just a simple adjustment that I will get done at the dealer during my first service.
- 7 replies
-
- cluster
- instrument
-
(and 3 more)
Tagged with:
-
I am installing a Kenwood DDX375BT in my 2005 Chevy Suburban Z71 with Bose sound system. I have purchased the PAC RP5-GM11 as my interface for the aftermarket radio. I do not like the chime module that comes with it. Is there a way to install a different chime module or am I stuck with this tinney module?
-
Newbie Here, Have a 1997 Regular Cab Silverado that I ordered replacement door handles for since the originals had a nice crack right along the lock cylinder. I was able to get the old handles removed and installed, but ran into an issue with one of the clips that attach the rear of the lock cylinder to the lock rod. I thought I could re-use the original, but sure as can be as soon as I got it all put back together and locked the truck a half a dozen times the old retaining clip slid off and now have to unlock the truck from the passenger side. I've attached what the original looked like and what I'm wondering may be a "potential" replacement / upgrade. 1. Anyone know where I can find that replacement clip? Is there some trick to putting it on without bending it? 2. Anyone tried using the plastic style clips here as a replacement and did they hold up ?