Jump to content

2014+ Suspension Lifts


Recommended Posts

6 inch pro comp premium with adjustable shocks

 

 

 

How do you like the ride of the ProComp coilovers? I plan on upgrading mine from the spacers pretty soon and I am debating going this route or some custom Icons, Fox's or SAW's.

Link to comment
Share on other sites

I'm not 100% sure, but mine had a 1/2" top mount spacer and it also had a bottom mount spacer that I thought measured 2". Here is something you can look at to see if your angles are maxed out. Look at your upper control arm (the top A arm) and see how close it is from hitting the droop stop right under it. If you have a half inch or so you'll be fine.

I thought this way too at first. I have a 2" level up front and its still 1.25" higher in the back. The block itself is only 1". So basically whatever the block measures to be.. Double it and thats your lift. Im thinkin about grttin 1/4 spacers for in top to raise it another half inch so itll get closer to level. These new trucks are raked too much now
Link to comment
Share on other sites

Fabtech 4" lift, 295/60/20 trail grapplers 20" BMF R.E.P.R's and debadged. I posted pics of the trimming needed in the fender well. Looks a lot better in person. Gears, black bear tune and corsa exhaust next.

post-127772-0-84143800-1394045676_thumb.jpg

post-127772-0-98116800-1394045724_thumb.jpg

post-127772-0-84143800-1394045676_thumb.jpg

post-127772-0-98116800-1394045724_thumb.jpg

post-127772-0-84143800-1394045676_thumb.jpg

post-127772-0-98116800-1394045724_thumb.jpg

post-127772-0-84143800-1394045676_thumb.jpg

post-127772-0-98116800-1394045724_thumb.jpg

  • Like 1
Link to comment
Share on other sites

Fabtech 4" lift, 295/60/20 trail grapplers 20" BMF R.E.P.R's and debadged. I posted pics of the trimming needed in the fender well. Looks a lot better in person. Gears, black bear tune and corsa exhaust next.

 

Looks good in the pictures!

What offset did you go with on the wheels?

Link to comment
Share on other sites

 

Looks good in the pictures!

What offset did you go with on the wheels?

Thanks, BMF only makes these wheels in 0 offset. It took some trimming but I think its the perfect offset, not too far in and not too far out.

Link to comment
Share on other sites

How do you like the ride of the ProComp coilovers? I plan on upgrading mine from the spacers pretty soon and I am debating going this route or some custom Icons, Fox's or SAW's.

sorry---- they are about the same as y Dirtlogic from Fabtech i had.. nothing bad to say about them at all...

  • Like 1
Link to comment
Share on other sites

I have the same setup but my tires are Falken wild peak and it rubbed about 1/8" so I just cut a little bit of the fender mat n wacked the back side of the sheet metal n no issues noweda8yqy4.jpgsadehy5y.jpgfingers width of clearance now.

 

Wicked Galaxy Note 3

 

 

Link to comment
Share on other sites

Hey there so right now I have a 2.5" leveling kit with 295/60/20 nittos. I was wondering if people on here with 4"-6" lift kits can still go through the automatic car wash. I'm thinking of putting a bigger lift on my truck. Would like to go 6". With winters like this in Michigan to cold to hand wash and I was it usually twice a week. Black truck gotta keep it clean. Thanks in advance!

  • Like 1
Link to comment
Share on other sites

sorry---- they are about the same as y Dirtlogic from Fabtech i had.. nothing bad to say about them at all...

Thanks, that makes the decision easier then. When it comes time to upgrade i will just roll with the ProComps and save a little money.

Edited by CAtaylor
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.