Sign up for FREE! Become a GM-Trucks.com Member Today!
In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience.
I am a proud owner of a GMC Yukon 2016 Denali. Since these cars are not officially available in Europe, I imported a Yukon. Basically, I am very satisfied with the vehicle.
But unfortunately, I have a problem with the vehicle, and nobody could help me so far: The car vibrates quite heavily and uncomfortably. The vibrations started when I stopped at the side of the road to let my wife get out. The engine lamp flashed, and the vehicle had hardly any power left. I drove about 1/4 mile, stopped again, and switched off the car. Afterward, I waited for over one minute and then restarted the car. The engine light stayed off, and so I was able to drive on. Also, the power was as usual again. But from there on I had vibrations which I didn't have before.
So I went to a service station to read out any errors and get some help. But there were no errors detected. Since the vibrations did not disappear on the next miles, I went to the dealer again. They reprogrammed the ECU unit with the latest software and balanced the tires. Nothing has changed. So I went to another dealer, hoping that it could help me in a better way. They told me that my tires were worn out and that they could cause the vibrations. We changed all four tires. The handling was a bit better afterward, but the vibrations remained.
Because in my country there are just about 10 GMC Yukon and a few Escalades driving around, no dealer has a clue and can solve my problem. Therefore I did a lot of research on the internet and on the paid platform of GM (ACDelco TDS) - unfortunately without success so far.
I am also familiar with the service bulletins for the 8-speed automatic transmission. But I can exclude these vibrations so far. I have some of these vibrations in my car. However, I have now imported the right oil from Texas by ship, and I will do the oil change within the next days.
But the other vibrations are noticeable at any speed, even at only 1 or 2 mph or over 100 mph. Especially when I ride uphill or downhill, it vibrates a lot. As if I had no suspension in the back and the vehicle would bounce around. The vibrations are mainly felt in the seat. Very slightly also in the steering wheel. From the beginning, my car tends to steer slightly to the left. But I never paid much attention to this, because measuring the track showed that everything is ok.
I am aware that a remote diagnosis is challenging. But perhaps you have any ideas where I should proceed with my further diagnosis? Is the suspension the right start, the drive shaft, or the wheel mounting? Or could it be the engine mounting? Or something completely different? What is the best way to proceed?
By Big R ED
Patient - 2019 1500 LD, 5.3, 6 sp, 7200 miles old, Covid-19 negative. Symptoms - 2-3 second shutter / shake / rumble, during light acceleration, 30-40 MPH and low RPM. Happens while both in V4 mode and while in v8 (manual w/ transmission set to L5). I thinks its the torque converter, but surfing the forum I see this issue mainly referenced to 2015+/- K2s and I'm not sure if they changed the trans in the final years. I'd appreciate either a TSB # or a link to another posting were I could find the TSB. I'd like to be able to take to my dealer and say "HERE....READ....FIX" (politely). Many thanks!
Hi everyone, new to the forum but I’m at the end of my ropes here this is my Hail Mary. So I have a 2016 Silverado crew cab 6.5’ bed 5.3l 4WD 6 speed automatic transmission. The transmission was fully rebuilt at 75,000 The truck has 89,000 miles on it. I am complaining about a shake/vibration of course but I don’t feel as if mine is like most. Mine doesn’t seem as violent as others describe. I’m experiencing a vibration and a noise almost like driving over rumble strip in the road. This problem comes about when you are gentle on the throttle and at a lower rpm around 1200-1500. If you feather the throttle at 55 MPH you can easily replicate the issue. Next is issue number 2 I’m not sure if they are related but my gut is telling me they are, I recently noticed when stopped then slowly take off as in just letting the truck roll at idle of the line I feel like a small wobble/bounce as it kind of rocks you back and forth in your seat. Both issues go away once you give it more throttle. I’ve had the torque converter replaced first once the issue came back I then I’ve changed the transmission fluid to the updated fluid, rotated the driveshaft 180 degrees and that has been the longest fix for 3 weeks. Any suggestions are helpful and appreciated and thanks in advance
This truck is my first 4WD/4x4. So a few weeks ago, I put my truck in 4HI, to drive in the snow, no issues. Put it back into 2WD, when I got home, and haven't needed it since, until this afternoon. When I put it in 4HI, it was grind/vibration central, but when I put it back in 4AUTO or 2WD, there is no issues.
Recently Browsing 0 members
No registered users viewing this page.
Most OnlineNewest Member
Who's Online 23 Members, 0 Anonymous, 1,110 Guests (See full list)