Jump to content

  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoticons maximum are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Juan7_4
      So this is my first post on here, been lurking around for a while and have been able to troubleshoot the majority of my problems. But most recently while leaving work truck started up just fine (2001 Silverado 4.3l vortec with 281k miles) and immediately stalled going in reverse tried cranking it and the battery died so I replaced it with a brand new one and it started up just fine and about 5 minutes down the road stalled again and would not start, towed it home and checked for basics fuel and spark, the truck is infact getting fuel even replaced the old fuel filter, the ignition coil has power and is sending power to distributor cap, checked spark plug wires and they aren’t reciving power and grounded a spark plug to check if it wasn’t getting any spark and it has not, replaced both rotor and cap and there is still no spark, all fuses are good, just no power to cap any help is appreciated 
    • By DenaliX14
      Hey guys just wanted to share tis bit of info that I was able to find. It was difficult locating a driveshaft for a 14+ GM 1500 so I hope this helps. 
       
      After spending tons of time trying to find a less complicated way to upgrade my DS I visited alldrivelines.com (referral from a member) and saw the 800hp rated 2 piece shaft. I called to verify compatibility and was let down by the rep. It is not user friendly for the 4x4's. 
       
      However, after asking me some great questions Shelby @ Alldrivelines  (661) 633-2303 simply said why don't you get our 1,200hp rated driveshaft for the 14+ GM 1500.. I said ..."wait huh". Tell me more. This is currently not listed on the website.  
       
      It is a 5" 6061 Aluminum shaft with a .125 wall thickness. It is rated for over 1,200 HP and 7,300 ft tq. She can get the correct size for other models too (bespoke).
      I'm running the following with a Stock Trans/Transfer Case and ride hight. 
      Make: GMC Model: Sierra 1500 Denali Drive: AWD/4WD Loc: Rear Bed: 5'9" Chassis: 143.5"WB Doors: 4 Door  
      After some negotiating it ended up being $580 SHIPPED from CA to MA!!!.  (She also suggested the upgraded billet slip yoke rated 1200hp it was an extra $100 so I'm actually $680.00 shipped)**
       
      Just a heads up folks. If you want a Driveshaft that can handle high speeds, high HP and TQ this is the place to go. Call Alldriveline (661) 633-2303 and ask for Shelby. Mention my last name Melaas and they'll cut you the same deal.
       
      A 1,200 hp rated shaft with the billet yolk for $680 shipped. I don't get anything for it I just asked if I could refer my friends here for the same deal and she said sure. Very nice Lady. 
       
      Lastly it is a 2-3 day processing and shipping for me (ca - ma) is about 3-4 days. I should have it next Thursday! I will send pics. 
       
      PM if you have any questions. 
    • By midwestdave33
      American Racing Headers Part number :GM62-14178300LSWC
      GM Truck 6.2L 2014-2019 Long System
      These have 150 miles on them. Like new! Cost $1,775 new. Passing a smoking deal on to you. Comes with all components originally sold as a kit from American Racing.

      ARH long tube headers long system for the 2014-2016 Chevy/GM Truck 6.2L features 304 stainless steel, 1-7/8" primaries, 3" merge collectors, and all the necessary hardware and gaskets for a bolt-on installation.

      The 2014 & Up GM Truck 6.2L ARH long systems were designed to bolt-on to your factory axle-back or any aftermarket axle-back. Some modification may be required. The American Racing headers require a crossover y-pipe assembly and have converters. Using the catted crossover pipe cause very little restriction and they help to control emissions.

      Product features on this system includes:

      100% Made in the USA - Never Outsourced

      Made entirely of 304 stainless steel

      3/8" thick laser-cut flanges for a warp-free seal

      Hand-ported TIG welded inlets

      Optimized primary tube routing for superior fit and performance

      Merge collectors with scavenger spikes

      Catted systems feature 200 cell metallic substrate catalytic converters for extreme durability
       
       
       

    • By brisk00
      Any had any experience with this kit?
       
      GM Dash Cam
       
      It seem interesting and possibly worth it.  It says it has built in ADAS so I'm curious what all that might add to the functionality of the vehicle seeing as this system actually plugs into the OBDII plug and communicates with the onboard computer.
       
      Thoughts?
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Forum Statistics

    208,490
    Total Topics
    2,232,807
    Total Posts
  • Member Statistics

    177,943
    Total Members
    8,960
    Most Online
    BlackB1rdy
    Newest Member
    BlackB1rdy
    Joined
  • Who's Online   87 Members, 0 Anonymous, 794 Guests (See full list)

×

Important Information

By using this site, you agree to our Terms of Use.