Jump to content

Recommended Posts

Center console in and works great. Thanks to Phil for the wiring harness.

Looks just like from the factory.

image000000.jpg

  • Like 1

Share this post


Link to post
Share on other sites

ALL,

 

I wanted to send an update to this thread.  The vendor where I purchase the yellow connector went obsolete.  I have spent the last 2 weeks trying to find another vendor with no luck.

 

What does this mean?

 

I'll have to purchase this connector directly from GM.  The cost for this connector is $15 more than what I used to get them for.  

 

SO... as of 9/1, the cost for this harness will have to increase by $15.

 

New harness price will be $150 on 9/1.  

 

Thanks everyone!

Share this post


Link to post
Share on other sites
Phil how can I add a wireless charging lid to my 2014 Silverado center floor console?

Do you have the full center console or the jump seat?


Sent from my iPhone using Tapatalk

Share this post


Link to post
Share on other sites

I would like to order a wiring harness for the jumpstart to center console how would I do it

  • Like 1

Share this post


Link to post
Share on other sites
I would like to order a wiring harness for the jumpstart to center console how would I do it

Send me a Pm.


Sent from my iPhone using Tapatalk

Share this post


Link to post
Share on other sites
I have the full center console. I received the pnp wiring harness from you.
 
Thanks

You’ll need to get a lid with the wireless charging module or see if you can add the module with the lid you have now.

Here is my video on it.

If you are able to add the module to the existing lid, you’ll need a cable to plug into the module and you’ll have to splice that into the rear 12V plug.




Sent from my iPhone using Tapatalk

Share this post


Link to post
Share on other sites

Quick question, How do you unplug the connectors for the 110 outlet. They won’t pull out with me. Not sure if there’s a tab I need to push in.

Share this post


Link to post
Share on other sites

Nvm I figured it out. There’s a tab on the side you need to push in for anyone else who didn’t know.

Share this post


Link to post
Share on other sites
1 hour ago, Abe879 said:

Nvm I figured it out. There’s a tab on the side you need to push in for anyone else who didn’t know.

I had the same problem with those 2 wires. Finally figured it out. The key is have patience and don’t mess anything up. 😊

 

  • Like 1

Share this post


Link to post
Share on other sites

Got it installed today everything works goodc3531522b735a834bd11780a97927570.jpg

Sent from my SM-G955U using Tapatalk

  • Like 2

Share this post


Link to post
Share on other sites

Finished my install.  All is working except the glove box USB.

I didn’t have any open USB’s on my HMI. 

2018 parts, so my iPhone 8 and wife’s X are wireless charging. 

Have my upgraded HMI on the way to get Apple car play and other later model features.  

Thanks for your help Phil!

758F4437-40CC-49A5-B74A-C0B1F4F9B577.jpeg

Edited by Baldhills
  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

    • By zmillstj
      Anybody have a jump seat from a 16 and up for sale? Need charcoal and as soon as possible. 
    • By 15sierra1500
      I was wondering if anybody knew if the newer 2018 sierra tail lights would somehow fit the 2015's? And if not, is there is a certain company making some custom ones for the 15' that are made to look like the 2018's? This is my first post to the group as I am new and will be asking more questions soon. So if I didnt do this right, please feel free to tell me how to correctly ask my next question. Thanks.
    • By pgamboa
      Jump Seat to Full Center Console Retrofit 
      Plug and Play Harness by PGAMBOA
       
       
      For those of you looking to swap your Jump Seat to a Full Center Console, I now have a Plug and Play Harness for this upgrade!  This long awaited - PnP Harness will allow you to EASILY perform this upgrade.  NO cutting or splicing needed!
       
      Center Console - Plug and Play Harness is $150 Shipped anywhere in the US.  For Canada, please add +$14.95
       
      Since there are several versions and configurations of center consoles and truck trim levels, I feel that I have covered a majority of the configurations that are out there.  There will be several assumptions on the ability to perform this upgrade and I’ll try to be as detailed and comprehensive as possible.
       
      Please see the different USB Cable configuration diagrams at the end.
       
      Assumptions:
       
      - I NEED to know if you have a 16-Pin Connector or 23-Pin Connector under your passenger seat.  GM made 2 styles and I can currently only build the 16-pin.  If you have the 23-Pin version, I can still build your a harness but I will need for you to pull your jump seat out, fully extract its harness, and send it to me.  This is the ONLY way I can make you are conversion harness.

      See pics below.

      23-Pin: Notice the grey latch.


      16-Pin:


      - 2014-2015 Center Consoles will have different USB Cable requirements than 2016-2017 AND will have different USB Hubs.  The PnP Harness should be compatible, but you MUST verify the connector under the passenger AND the front of the console!  Since this is a custom product, there will be NO REFUNDS on it.
       
      - Center Console MUST have its factory harness intact and not modified.
       
      - Connection under the Passenger Seat AND Front of Center Console must look exactly like the diagram.  There is a 23-Pin variant X314 Connector under the seat, so yours MUST match in order for this harness to adapt.  **IF YOU HAVE THE 23-PIN VERSION, I CAN STILL BUILD YOU A HARNESS BUT WOULD NEED YOUR ORIGINAL JUMP SEAT HARNESS SHIPPED TO ME FIRST**
       
      - Additional GM USB Cables must be purchased separately (based on your console year) to get USB Hubs functional.
       
      - Wireless Charging - Wireless Charging became available on 2016 and 2017 consoles.  If you are looking at adding a Wireless Charging Lid to a 2014-2015 Console, please PM me for requirements.  Also, there are known issues with 2016/2017 Consoles with the Wireless Lid and charging iPhone 8 and iPhone X Phones.  There are workarounds for this that require some form of modification to the charging module.  You can also swap the module for a 2018 Module that DOES charge iPhone 8 and iPhone X phones.  Please PM me for questions on specifics.
       
      - Your truck MUST have an existing 110V AC Outlet AND (1) - 12V DC Cigarette Lighter Plug as you will be reusing those.  My PnP Harness DOES NOT add the 110V AC Outlet if you don’t already have it.  However, I CAN add an additional 12V DC Outlet connection if needed.
       
      - USB Cable connections will come from your HMI (Behind the Glove Box).  You MUST verify that you have the USB Ports available, otherwise, your USB Hubs will not work correctly.
       
      - This PnP harness DOES NOT add any Car Play, Apple Play, or Android Play functionality.  If your truck did not already come with it, you will not gain it.
      With this PnP Harness, you ***should*** have ALL the components in your console functional.
       
      Those options include:
       
      Front of the Console:
      Front - Left USB Hub (Dual USB - 2016/2017or Triple USB Hub 2014/2015 - Uses my Plug and Harness AND a USB Cable from the HMI Front - Left 12V DC Cigarette Lighter Outlet - Uses existing connections (truck must be equipped.  If not, I can custom add this if needed) Front - Right 12V DC Cigarette Lighter Outlet -  Uses my Plug and Play Harness Front - Right 110V AC Outlet - Uses existing connections (truck must be equipped)  
      Inside Storage Compartment:
      Inside - Left 12V DC Cigarette Lighter Outlet - Uses my Plug and Play Harness plugged into the front main 42-Way Connector Inside - Right USB Hub - Uses my Plug and Play Harness plugged in the front main 42-Way Connector and USB Cable Inside - Right SD Card Slot (if equipped) - Uses my Plug and Play Harness plugged in the front main 42-Way Connector and USB Cable Inside - Right 3.5mm Aux Port - Uses my Plug and Play Harness plugged in the front main 42-Way Connector and USB Cable Inside - LED Lamp - Uses my Plug and Play Harness plugged into the front main 42-Way Connector Wireless Charging Lid (For Consoles that come equipped with this option) - Uses my Plug and Play Harness plugged into the front main 42-Way Connector  
      Rear of the Console:
      12V DC - Cigarette Lighter Outlet - Uses my Plug and Play Harness plugged into the front main 42-Way Connector  
      THERE IS A LOT TO CONSUME HERE, SO PLEASE PM IF YOU HAVE QUESTIONS ON THIS.  I WANT ENSURE THAT YOU UNDERSTAND ALL THE REQUIREMENT FOR THIS RETROFIT BEFORE PURCHASING.
       
       








       
       
  • Recently Browsing   1 member

  • Forum Statistics

    207,497
    Total Topics
    2,220,506
    Total Posts
  • Member Statistics

    176,817
    Total Members
    8,960
    Most Online
    Arment
    Newest Member
    Arment
    Joined
  • Who's Online   144 Members, 0 Anonymous, 1,150 Guests (See full list)

×

Important Information

By using this site, you agree to our Terms of Use.