Jump to content

madsen203

Isolating ticking sound on drivers side

Recommended Posts

I'm doing my best to isolate this ticking sound that is persistent, yet intermittent. 

 

Data so far: 

2018 CC SLT 1500 6.2L 4WD Max Tow 19K miles, all stock

  • Doesn't happen when motor is cold, much more prevalent when motor is warmed
  • Doesn't happen when letting off throttle (only under application of throttle), can be heard in neutral, park, and in drive (not in reverse enough to tell--but it happens when transmission is not engaged)
  • Sound follows steady or increasing RPM of motor
  • Under light to medium load, noise is prevalent, under heavy acceleration it subsides (not because of engine noise)
  • If I turn wheels hard left, the noise disappears, straighten wheels, it returns (like wheel is blocking noise from traveling)
  • Sound only heard on driver side
  • If I hit some oscillating bumps on the road, it can stop for a while before returning back (under varying loads as well)
  • If left in tow/haul mode, at 2500 rpm under light load it can still be heard
  • Ran 2 bottles of Red Line injector cleaner and it didn't eliminate/help noise
  • The truck was silent until the 700 mile mark and I hit an expansion joint (nothing out of the ordinary) and the sound started and has remained ever since
  • I've checked exhaust/manifold connectors and no sign of leaks (soot)
  • I put a hollow aluminum rod (2 foot long) to the vacuum pump and did not hear any abnormal noises directly from the pump
  • Obviously heard injector noises when put to the injectors; haven't had chance to stop on side of road when the sound disappears to run comparison tests
  • Sometimes it'll run dead silent when driving down the road (after complete warm up) and power delivery doesn't change but noise comes back within a minute or two
  • Sound heard in both V-8 and V-4 modes, and while in manual shift mode
  • Use premium 91 gas ever since purchase (93 not available in Bay Area)--use Costco Top Tier fuel (high volume station)
  • Oil changed with Mobil 0-20W Full Synthetic every 5K miles religiously and OEM filters (indicator usually states 37% remaining at around 5k miles)
  • 90/10 Highway/City driving

 

Any thoughts? My MPG is seems close to normal. Lifetime average of 17, most of my time driving is short city trips or long highway driving with a bed full of gear and a dirt bike. 

 

Some of the actions seem like it could be a noise related to the vacuum pump but the pump doesn't exhibit any noises itself. Sounds kind of like exhaust leak--exhaust seems to check out (no notable soot around connections or along piping that is visible). If it was something loose, I would think that even under deceleration (letting off throttle) would cause the noise to persist. It follows increasing RPM. 

 

I've checked around the footwell and haven't noiced any plugs missing or issues there. The fact that the sound is not there when cold or after some bumpy roads makes me think something else is up. 

 

Thoughts? Things to check? 

 

When it is quiet, this truck is wonderful. The ticking in the background that comes and goes is like a form of Chinese water torture. The fact that it does go away sometimes makes me even crazier as I know it could be better. When I bought it, it did not make this noise. Only after 700 miles of driving did it begin to tick tick tick away. 

 

 

 

 

 

 

 

 

Edited by madsen203
Additional information added

Share this post


Link to post
Share on other sites

I've had this noise for a year and a half. I recently had my vacuum pump replaced and the steering shaft boot. The noise was gone for a month but it is now back but not as loud. So either my new vacuum pump is starting to crap the bed or the steering shaft boot is not seated properly. I personally think it's the boot 

Share this post


Link to post
Share on other sites

I hear the same noise, I believed it to be the injectors firing. Honestly I never noticed it till I was in the truck with two other people in in and the radio was off as we we're talking. During the times of no conversation I began to notice it. It's very faint. And now that I've heard it once, it's like I hear it every time , it's very very faint and only hear if the radio is off and no one is talking.

Share this post


Link to post
Share on other sites

I am 98% sure it is this. The noise dissipating when turning left led me to finding this. Thanks GM forums! 

 

Also thanks to this forum I found the TSB that addressed the rear back up camera at full brightness at night. The dealer checked the lifters and all is fine. Ready to get this over and done with! 

 

Share this post


Link to post
Share on other sites

I have a ticking from passenger door. I think it’s one of the lock or window switches

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

    • By sambone95
      For the last 5,000 miles or so, I have noticed a (louder than normal) ticking noise coming from my engine bay. Recently. while navigating a parking garage at the airport, I lost all brake boost vacuum and almost hit a column. I did some research and found all of the info online relating to the NHTSA investigation etc.
       
      I went to my local dealership. They wanted $900 to replace the vacuum pump. It broke out as $615 in labor and $285 in parts. After looking around online, I couldn’t find a detailed write-up or video on this repair. I put together a write-up for anyone else who might want to save a few hundred bucks
       
      Be easy on me, I do a little light mechanical work but and have never done a write-up. I’m sure I screwed some things up…
       
       
      Supplies I Used:
       
      ·       Flathead Screwdriver
      ·       Plastic Pry Tool
      ·       Small Hook Pick
      ·       3/8-in Ratchet
      ·       3/8-in Torque Wrench
      ·       3/8-in Drive 3-in Extension
      ·       3/8-in Drive 6-in Extension
      ·       1/2-in Drive 24-in Breaker Bar
      ·       1/2-in Drive 5-in Extension
      ·       10mm Socket (3/8-in drive)
      ·       11mm Socket (3/8-in drive)
      ·       15mm Socket (3/8-in drive)
      ·       24mm Socket (1/2-in drive)
      ·       7 Quart Drain Pan
      ·       OEM Stretch Belt Installation/Removal Tool (AutoZone Loaner P/N 27272)
      ·       Red Paint Pen
      ·       Small Bungee Cord
      ·       Medium Strength Threadlocker
       
      Replacement Part:
      ·       ACDelco GM Original Equipment Vacuum Pump -- P/N 12669488 (I bought it from gmpartsgiant for about $130 shipped)
       
       
      Step 1 – Prep the Workspace:
      Park the truck on a level surface Lock steering wheel about 1/16th of rotation right of center Disconnect the negative battery terminal Remove the plastic skid plate/shielding from below the engine compartment (four 10mm and two 15mm bolts) Place the drain pan on the ground below the vacuum pump Pull the air intake tube away from the throttle body to give access to the crank pulley from above Disconnect the two crank case vent hoses from the intake Disconnect the intake from the throttle body by loosening the clamp and pulling it back Pull the intake up and toward the passenger side. Secure it, out of the way, using a bungee cord Cover the throttle body intake with a plastic bag, secure with a rubber band  
       
      Step 2 – Remove the Lower Steering Shaft
      With the paint pen, mark the steering shafts at the connection points between the intermediate steering shaft and the steering gearbox input shaft. This will be used for reference at reinstallation. With the steering wheel locked about 1/16th of a rotation right of center, the upper bolt (closest to the firewall) of the lower steering shaft easily accessible. Using a 15mm socket, remove the bolt. Note: The upper bolt is secured with a collared nut that wraps around the shaft. When the bolt is completely removed, you should be able pop the nut off the shaft. Moving down the shaft, there is an 11mm bolt that fastens the lower steering shaft to the steering gearbox input shaft. I was able to easily access this bolt by unlocking the steering wheel and slightly moving the wheel toward center. Remove the 11mm bolt. With both bolts removed, remove the lower steering shaft from the steering gearbox input shaft by pulling upward. Once the lower steering shaft is separated from the input shaft, slide the lower shaft down and toward the front of the vehicle to separate the lower shaft from the intermediate shaft.  
      Step 3 – Remove the Vacuum Pump
      Place the stretch belt removal tool on the vacuum pump pulley. Using the 1/2-in drive 24-in breaker bar, 24mm socket and 5-in extension, turn the crank pulley until the belt slips off the vacuum pump pulley. Follow the vacuum line from the brake booster to the vacuum pump. Using the plastic pry tool, separate pressure fit fasteners holding the vacuum line in place. Additionally, remove the pressure fit fastener securing a wire loom to the pump Using the hook pick, carefully remove the retaining clip where the vacuum hose is attached to the vacuum pump. Note: There is a heatshield around this fitting the will need to be carefully peeled back. Separate the vacuum hose from the pump and rotate the hose out of the work area. Four bolts secure the vacuum pump in place. Using a the 11mm socket and a combination of the 3/8-in drive extensions, loosen all four bolts. While holding the vacuum pump in place, finish removing all four bolts and separate the pump and gasket from its mounting point. Note: About 1/4 to 1/3 of a quart of oil will leak out into the drain pan during this process. Lift the pump out while rotating it around the wire looms and belts (this will take some finagling).
        Step 4 – Install the New Vacuum Pump
      Coming from the top, rotate the new pump into position. Note: The pump I bought came with four new bolts and a new gasket. While ensuring that the gasket is firmly in place, use the 11mm socket and extensions to finger tighten the four bolts. With the 3/8-in drive torque wrench, torque the four bolts to 23 ft/lbs. Note: I called my dealership service department and was told the torque specs over the phone. I have no documentation showing the specs Rotate the vacuum hose back into location and attach to the pump. Snap the retaining clip back into place and put the heat shield back into position. Push the pressure fit fasteners back into position Using the reverse process of removal, reinstall the belt. Note: if you are reusing the same belt, be sure to check that it is in acceptable condition for reuse.
        Step 5 – Reinstall the Lower Steering Shaft
      Lining up the paint pen marks, slide the lower steering shaft back onto the intermediate steering shaft. Once the lower shaft and intermediate shaft are together, slide the lower shaft onto the steering gearbox input shaft. Apply the threadlocker to both bolts. Reinstall each bolt (15mm and 11mm) and torque to 35 ft/lbs. Note: I called my dealership service department and was told the torque specs over the phone. I have no documentation showing the specs.
      Step 6 – Reinstallation of Workspace Items
      Reinstall air intake tube using the reverse process outlined in step 1. Reinstall the plastic skid plate/shielding from below the engine compartment (four 10mm and two 15mm bolts). Connect the negative battery terminal. Check engine oil. Refill as needed (1/4 to 1/3 quart)  
    • By Shaversilverado
      Looking for help/instructions on replacing fuel injector/s for a 2017 5.3L Silverado. Truck has 80K miles on it and a #5  misfire. Dealer ran a diagnostics and said the injector needs to be replaced.
       
      I found a couple pictures on the forum of the fuel injectors but very little information on steps to replace them. The only videos I could find online were for older models with a different injector diagram. Talking to the dealer they quoted me $770 to replace a single injector, gaskets and piping associated with the job. 4 hours or labor and $240 in parts. 
       
      Are there any good instructions or videos out there on replacing fuel injectors on a 2017 Silverado?
      I've never done a job like this but consider myself mechanically include, is this an easy enough job or should I leave this to the dealer to do?
      I know they say if your replacing a single injector you might as well replace all 4 on one bank but is that really necessary, $110 a piece and if the other 3 are fine why replace them?
       
      The dealer said the piping and gaskets must be replaced even for a single injector replacement job. Is this all necessary? I've never had another vehicle with injector problems so this will be a first. 
      Parts quoted-
      12687650           (1) injector
      12626354           (8) gaskets
      12677002           (1)  pipe
      12677004           (1) pipe
       
      Any help, links to instruction/diagrams or videos would be awesome! I enjoy working on these projects rather than paying someone else to do the work since you learn something every time. I also want it done right.
       
      Thanks all in advance!
       
       



    • By Ozer
      https://www.whec.com/news/gm-under-investigation-for-faulty-brake-vacuum-pumps/5154566/?cat=565
       
      "The U.S. government is investigating more than 100 complaints of poor brake performance on 2.7 million General Motors big pickups and SUVs."
       
      Hold your receipts if you have done any work, hopefully a recall comes out of this. 
      I also think reporting your issues to the NHTSA may get this rolling out faster.
    • By Bunky
      Ok so a while back I posted about my 2500HD running rough, I changed the Injectors  (2 weren’t firing) and then it ran  as bad if not worse and started knocking.   
       
      Well today day I finally got around to pulling the engine apart to find #3 rod broke in half and into pieces.   Anyone have any ideas  on what happened?
    • By Burban2007
      I recently did a dod delete on my 2007 suburban. 6.0 200,000 miles. I thought the problem was the afm lifters being that there was a tick at highway speeds. I only had a tick at highway speeds. If I drove on the street I would never get the noise. As soon as I held a steady speed on the highway I would get what sounds like a lifter tick. The dod delete work was done by a Preformance shop. I do not think that dod was the problem. If I hold the throttle steady at 2000rpm while in park I can get the tick to come on. After I let the engine idle about 2-3 minutes the tick goes away. As soon as I hold the rpms back up it will come back and repeat the process. No loss of power while this is happening and no other sounds. Oil pressure is about 10-15 at idle and close to 40 while on highway. I would greatly appreciate any help. 
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Forum Statistics

    205,544
    Total Topics
    2,196,863
    Total Posts
  • Member Statistics

    174,799
    Total Members
    8,960
    Most Online
    14 sierra
    Newest Member
    14 sierra
    Joined
  • Who's Online   138 Members, 0 Anonymous, 1,023 Guests (See full list)

×

Important Information

By using this site, you agree to our Terms of Use.