-
Similar Content
-
07 silverado P0420 and P0054 codes. Already replaced o2 sensor and found a bad fuse, still having this issue
By James Hau,
- 3 replies
- 4,830 views
-
- 3 replies
- 4,899 views
-
- 1 reply
- 7,591 views
-
- 12 replies
- 7,749 views
-
- 3 replies
- 2,083 views
-
-
Recently Browsing 0 members
- No registered users viewing this page.
-
Forum Statistics
250.3k
Total Topics2.7m
Total Posts -
Member Statistics
342,698
Total Members8,960
Most Online
-
Who's Online 12 Members, 1 Anonymous, 543 Guests (See full list)
-
Latest Articles
-
Posts
-
By richard wysong · Posted
same here no change, scare tactics trying to get folks to hoard? -
By asilverblazer · Posted
What is that going to fix? (Besides a bunch of breaking a bunch of manifold bolts...) Are they cracked? Touching them will likely cause more problems than a little rust. -
By asilverblazer · Posted
For a 2000 model - GMT 800 the pattern is: For a 2014: Fron seat mount spacing looks identical - enjoy. -
By asilverblazer · Posted
That's not what I was talking about. I have not seen it specifically documented that bottom of the hatched area equates to "1 quart low". I've never measured or compared a dipstick reading at the bottom of the acceptable range, added 1 quart, took a new reading and it be exactly at the top of the range. My view of the manual is if it is BELOW the mark, add one quart at a time until the level is within the hatched area, 1 quart could put it 1/4, 1/3, 1/2 all the way there. I don't know, none of mine have been BELOW the mark to require adding any to find out. However, if over 400 miles it takes multiple quarts to keep it in the hatched area, yes, that is a problem. EDIT: None of my vehicles have ever been to the bottom of the range, every check shows them give or take somewhere on the top half of range. (I might even challenge my own memory and say at worst the top 3/4s.) Never to the bottom, much less below the "add" mark, so I've never added 1 quart to see how much it moves the level up the stick. Circling back to my point, the volume coming out is less than what everyone suggests my dipstick readings should be indicating. If from the top to bottom mark of the hatched area equates to 1 quart of oil, I would see the dipstick reading (on every vehicle I've touched in the last 30 years) be at the top of the mark when I fill with new oil and be at the bottom just prior to changing; based on what I am measuring in the drain pan. However, the dipstick readings are NOT showing that amount of drop. See above. -
Anyone have any experience with adding the autosense module to a high trim suburban/tahoe? 2026 Chevy Suburban High Country - Did not have the "tech pkg" but does have the High Country Deluxe pkg. Absolutely wild this is not a standard feature. OEM route - if it's already a powered hatch, has anyone tried to install the module for the hands free and tried to get GM to reprogram the BCM? Aftermarket route - if OEM is impossible or too much of hassle, does anyone have any experience with aftermarket hands free sensor options? I know Ensight Automotive does the conversions, and I've read a little about ISS Automotive. Any experience with these options/vendors?
-
-
GM-Trucks.com Clubs
-
Black Truck Club
Open Club · 612 members
-
White Truck Club
Open Club · 380 members
-
Canadian Owners Club
Open Club · 282 members
-
Red Truck Club
Open Club · 156 members
-
diesel 3.0
Open Club · 279 members
-
Texas Owner's Group
Open Club · 371 members
-
NorthSky Blue Club
Open Club · 118 members
-
Midwest Owner's Group
Open Club · 212 members
-
2015 Custom Sport Club
Open Club · 5 members
-
GM Snow Plowing Club HD
Closed Club · 14 members
-
-
Popular Contributors
-
.thumb.JPG.2c573de60d3a3a4407c7d92298db46dd.JPG)
Recommended Posts
Archived
This topic is now archived and is closed to further replies.