-
Sign up for FREE! Become a GM-Trucks.com Member Today!
In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience.
Steering Issues
-
Similar Content
-
By Cross1992
Hello,
I am about to buy a 6.6L Duramax 14' 2500hd Sierra with 136K on it. But I just learned it has a small heating core leak, the dealer is replacing the whole core prior to purchase. Should I proceed with this purchase? Or is this the sign of this truck going down hill. The service recorded were regular until 2018 then the car fax no longer shows any updates.
Any help would be appreciated, I have a 92 Sierra with a 5.7L small block so the diesel world I am not as comfortable with. Also do not want a newer truck as I do not want to deal with DEF and I would not be able to do a delete.
-
By Dillion Padgett
I recently bought a (Gen 3) LQ4.
I'm trying to swap this into an (Gen 4) 07' Silverado which uses 58x Reluctor, 4x Cam Gear, Front Timing Cover/Crank Sensor, and 2 Knock Sensors located in the sides of the block.
I have a (Gen 4) Truck, So the timing cover/ crank sensor/ knock sensors can be used. I also have a (Gen 4) ECM/Harness.
I know I need to get 58x Reluctor Gear put on & get a 4x cam gear already
My questions are as follows:
1. Can I put a 4x Cam Gear on a (Gen 3 Cam) ? or do I need to get a (Gen 4 Cam) for the (Gen 4 Cam Gear) to work ?
2. Can I use the (Gen 4 Knock sensors) on the side of the (Gen 3 LQ4) ? Just drill/tap & mount them ?
3. If I keep the (Gen 4 Fuel Setup) could I just install that on the (Gen 3 LQ4) ?
Any help or advice will be appreciated.
I'll be documenting everything so others will have better knowledge when putting a Gen 3 Block into a Gen 4 Vehicle.
Thanks guys !
-
By 04z71crew
Brand new oem bosch injectors for an LML 2011 through 2016.
$2,600 for the complete set of (8) shipped anywhere in the contiguous U.S. NO cores are required.
-
By Duramaxz
Don’t know the rules and regulations round here, just looking to swap anyone for a center console on a 2500hd 2020 for my leather jump seat with storage.
email [email protected]
thanks Z 💨 💨 💨
-
-
Recently Browsing 0 members
- No registered users viewing this page.
-
Forum Statistics
241.5k
Total Topics1.4m
Total Posts -
Member Statistics
-
Who's Online 36 Members, 0 Anonymous, 1,188 Guests (See full list)
- mbaee
- Mark Hickton
- Steve-2019
- poppy510
- Custom 68
- Bobs78
- TheBigBadWolf
- Tanner Gragg
- PureZ71
- rav3
- millwright1178
- Travis Huffman
- rosevelt jackson
- Traction
- Another JR
- Tay2610
- Jettech1
- Paul Banks
- mikeyk101
- richard wysong
- Stallion_08
- Gary Camille
- JimCost2014
- steelerdude15
- alrockaz
- Az JJK
- 03Jarhead
- Grumpy Bear
- country_09
- pigpen23
- Pryme
- Plympat
- Curl510
- Kyle Creeden
- Mass2500HD
- josney
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.