Jump to content
  • Sign up for FREE! Become a GM-Trucks.com Member Today!

    In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. 

Recommended Posts

I have had this happen twice, #7 intake lifter and cam lobe are wasted any ideas or suggestions 350 small block 010 block.

Share this post


Link to post
Share on other sites

Not enough information. Lifter type? Cam factory? This a simple cam swap situation or a rebuild? Assembly lube used? What oil? How is it being broken in? Is the system primed before fire up. How many miles to failure. See where this is going? 

Share this post


Link to post
Share on other sites

Engine only has 3k miles since build.First time had engine miss, tore down and found #7 intake lobe and lifter rounded. Checked head, springs, roller rockers, performance push rods, and lifter journal.  All looked good. Replaced cam with a slight performance cam and all new lifters. Used black paste on all lobes and lifter bottoms also used break in additives. #7 lobe and lifter rounded again before break in was done. Appeared all rockers were getting good oil. I'm lost.

Share this post


Link to post
Share on other sites

It's odd that it's the same place twice. Did you do an interference check? How? 

Share this post


Link to post
Share on other sites

What I meant was did you roll the motor over by hand checking everything that can make contact. Not just does it have clearance but is it enough. Your cam manufacture will have minimums. Also as it is the same position did you check the spring pressures. Weak spring. Enough spring. You changed to a 'performance' cam. Matching springs? Clay the pistons? Is there something funky with that lifters bore? Oil feed or clearance? BTW, what oil are you breaking this motor in with? 

 

Yea, I'm fishing as I'm not there and can't see what you see and don't know this build or the builder.  

 

 

 

 

 

Share this post


Link to post
Share on other sites

All clearances look good. I'm still thinking oiling issue with that lifter bore. All springs are for the cam and were double checked at the machine shop after it happened the second time. Do the lifters get there oil from the hole inside the lifter bore?

Share this post


Link to post
Share on other sites
Posted (edited)
3 minutes ago, Pete Kerns said:

All clearances look good. I'm still thinking oiling issue with that lifter bore. All springs are for the cam and were double checked at the machine shop after it happened the second time. Do the lifters get there oil from the hole inside the lifter bore?

Yep. The lobe however is mainly splash. 

 

Edited by Grumpy Bear

Share this post


Link to post
Share on other sites

Tell me about the cam. Hydraulic? Solid? Mild as in used OEM springs mild?

 

And again what oil are you trying to get this bird off the ground with.

Share this post


Link to post
Share on other sites

I understand al the questions,  but all of them answers won't explain why it happened twice in the same spot. 

Share this post


Link to post
Share on other sites
Posted (edited)

Okay 

:seeya:

 

 

Edited by Grumpy Bear

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.