Jump to content
  • Sign up for FREE! Become a GM-Trucks.com Member Today!

    In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. 

Recommended Posts

Anyone else mounted  BFGoodrich KO2's on their Silverado? We just had these delivered yesterday. 50% of our dual rubber strategy. KO2's for winter/off-road and something else on our Chevrolet Performance 22's for the summer and highway. We stayed with the stock sizing the 20's. 275/60/R20 

 

We LOVED the KO2's on our 2011 Sierra. It made the truck look so mean. I'll post after photos in a few weeks when we get them mounted!

 

gmtc_bfg_ko2.jpg

  • Like 1
Link to post
Share on other sites
  • 2 weeks later...

I had them put on at 8,000 mi and now have 44,000. The 10 ply KO's have been great, only half tread life worn and I keep them on year round with 38psi.  I'll buy them again when the time comes, I like the look also.

Z71 Side II.jpg

Link to post
Share on other sites

i put almost 90k  on a set those puppys.....granted they were worse than fried!!!... but no flats and thats when i replaced them......would not hesitate to put on another set.....

Link to post
Share on other sites

The best in the business . Not saying there arent other good AT tries out but these are legends. 

 

Why not go a little bigger though ? Like 65 profile ? 

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Austin Poff
      Hey guys! New to the forum here. Previously had a Tacoma and switched to a 1500. 
       
      Wanting to do a 5” lift on my 2020 LT and thinking about doing 33.5s on 12x10s. Does anyone have any pics here I could see that are similar? Looking at 275/60/r20s
       
      thanks all! 
    • By austin jez
      Hello all. I have a 2013 silverado w/5.3l flex vin 7. Basically has rough idle in park and drive. Very poor acceleration. Almost seems to bog down when trying to accelerate. It will occasionally surge and for just a split second I can feel a bit of power.  Also doesn't want to downshift when I lean on the gas pretty heavy. I've got to do near floor it to get it to down ****** and when it does it will drop down 2 gears a lot of the time. No engine light and it won't set any codes. Showed 0 misfires on all cylinders. Long Fuel trims usually in single digits negs. Fuel pressure 43-46psi at idle and highway. I've replaced throttle position sensor, Accelerator pedal position sensor, manifold pressure sensor, mass air sensor, plugs, coolant temp sensor, oxygen sensors. Fuel pump, intake manifold gaskets twice (now with "updated" steel gaskets), throttle body gasket/seal, injector o-rings (upper and lower). Tested all coils for strong spark. Smoke tested for vac leaks along with propane. It has never failed to start or even had a long start and has never died/stalled. I'm just kinda at a loss at this point. Any help will be appreciated and possibly considered. Thanks
    • By gbux07
      I am wondering if I can fit 35s on a 3in body lift on a 2013 Silverado Z71 4x4. Will I need wheel spacers or offset wheels? Will stock 18in rims work or do I need aftermarket ones? Thanks
    • By JetForceF22
      Hello Everyone! Before I get started I want to thank anyone in advanced who responds with pertinent information. 

      I'm looking for a replacement exhaust system for my 09 Silverado 6.2L 4x4 Crew Cab/Short Bed. My current system has lots of rust (living in MD, they heavily salt & brine the roads here) and has sprung an exhaust leak right behind the muffler on one of the pipes.

      I've been searching around (thought it would be easy to find a system) but have not had luck in finding what I have been searching for. There are plenty of systems for 5.3L & 6.0L motors but scant any for 6.2L. 

      On my truck currently is an aftermarket cat back system that was there when I bought the truck (not sure which brand.) It is a single in / dual out muffler with dual pipes going out the bumper.

      Questions:
      What is the factory flange diameter at the end of the factory Y pipe? I'm seeing conflicting information (this will help me determine what muffler to buy if I piece meal a system together) 

      If you have any suggested systems, here's what I'm looking for
      Material: 304L Stainless Steel
      Volume: Loud/Agressive
      Configuration: Dual exit at rear bumper

      I'd consider a long tube header setup w/ high flow cats as well (I would like to maintain all emissions equipment) any suggestions there are also welcome. 

      I can always get a quote from a shop but I wanted to shop around first before I did that. 
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Forum Statistics

    234,354
    Total Topics
    2,492,606
    Total Posts
  • Member Statistics

    256,378
    Total Members
    8,960
    Most Online
    Dave6066
    Newest Member
    Dave6066
    Joined
  • Who's Online   57 Members, 0 Anonymous, 3,604 Guests (See full list)



×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.