Jump to content
  • Sign up for FREE! Become a GM-Trucks.com Member Today!

    In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. 

2022 Silverado 2500HD 6.6 Gas Payload (CC SB)


Recommended Posts

On 12/6/2021 at 8:47 AM, newdude said:

 

Back on topic.  Why not have just put on a tire that is more aggressive than those so called "AT" Michelin LTX AT2 but less aggressive than the Hankook Dynapro MT2?  Something like the Firestone Destination XT that would potentially offer more sway control and not lead to a towing reduction?

 

Firestone Destination X/T | LT275/70R18 (tirerack.com)

 

I believe Firestone does not sell destination to oems.  It is only an aftermarket tire.  The aggresive tire market is growing and they are difficult to develop to maintain off road ability without making tradeoffs in handling, tire uniformity, rolling resistance, noise passby, or stopping distance.  There is some new tech coming that helps balance those.  You will see some aggressive tires in future with a better balance.  

 

#iworkforGM

Link to comment
Share on other sites

Thanks to all the good folks who listed the options, and picture of the decals.  That is a big help!

Also thanks to the OP who titled this thread very clearly.  Very helpful to others looking for specific info.

:cheers:

Link to comment
Share on other sites

34 minutes ago, sheath said:

Thanks to all the good folks who listed the options, and picture of the decals.  That is a big help!

Also thanks to the OP who titled this thread very clearly.  Very helpful to others looking for specific info.

:cheers:

Hopefully it's helpful!

 

I found this 2020 Gas 2500HD High Country CC SB at a local dealership. 

Heated leather bucket seats, bed liner, sunroof, etc. No 5th wheel prep or tailgate step.

 

3346# payload capacity.

20211213_185018.jpg

20211213_185031.jpg

29237337719.jpg

29237337737.jpg

29237337836.jpg

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Content

    • By Lowerdz964
      So after some digging I found the build thread section. 
       
      What we have here is my 2014 Crew Cab Z71 4WD short bed queen. Bought a few years back as my daily work truck to put my weekend warrior back in the garage. When I first snagged her she was lifted on 34s and by the first drive home I knew the tranny was blown. Worked out a deal with the dealer I bought it from and had a 100k warranty remain installed where they paid for half of T&M. Factory crap struts with spacers front to rear came on her for a "lift". Within a few months I installed ICON Stage 1 kit to give her that quality ride effect. Love me some ICON, ride was supple on and off the road with this kit. When I decided to let go of the weekend warrior to fund the wife's new ride and changed industry's I got the itch to go back to my roots and slam her. I know I wanted to follow the same concept I did with my last mini must haves.
       
      Suspension must haves:
      Adjustable Coil Overs up front Adjustable emulsions in the rear (I went back and forth for months if this was needed on a full-size before realizing it was a MUST HAVE) Control arms up front due to 4wd and limited spindle offerings  Flip in the rear 22x10 that sat flush if not almost flush and this go around the wheel set had to be SQUARE  
      After quite a bit of research I came up with the following mods, mind you not all at once
       
      Mod weekend 1:
      IHC 4/6 drop kit Front and Rear, dialed (according to my comparison from ground-to-fender measure on a 19' Z71) she sits right at 4/6 and within spec on alignment.
      IHC 4" drop arms (Front) Belltech 2-Way Adjustable Coilovers (Front) IHC Axle Flip kit (Rear) IHC 1" lowering shackle (Rear) IHC drop shocks (Rear) Wheels and Tires 22x10 square ET +0
      Cosmis racing XT-206R (finish chips easily but they also clean up easily) Lionhart 285/40/22 (Surprisingly nice ply and quieter than anticipated)  
      After the initial mod weekend truck sat with a Carolina Squat 🤮, the rear shocks had no ass in them and my measured adjustment on the coil overs were perfect however I did install per IHC instructions with the 1/2" spacers raising the front 1". Trucks rear was as soft as a yellow belly teenager, I would bottom out axle to frame and pumpkin to bed every where I went. This was not my experience on my first go around on a full-size (96' extended cab bow-tie w/ 2/4). I was able to load that rear end up with dirt bikes and motors all day long without issue, guess there was a leaf design change over a span of 18 years 🤣. After a week of banging down the freeway I pulled the trigger on IHC helper bag kit and QA-1 shocks within spec of the drop shocks from IHC (eye-to-eye extended and fully compressed). I made the mistake of purchasing Belltech adjustable drop shocks, these only work for 4" rear drops to my dismay 😔. I also noticed that the drop shackle in the OEM hanger configuration was rubbing at ride height, so purchased the shackle flip kit from IHC as well.
       
      Mod weekend 2:
      IHC Shackle Flip Kit (allows for cleaner travel of suspension, simply shoving lowering shackle onto system was rubbing frame) IHC 1" drop shackles IHC Firestone helper bag kit (Rear) QA1 2-way adjustable emulsion shocks (Rear) Designed and Machined custom bushings to accept the OEM bolts (Inventor and Xometry FTW)  
      Once I installed QA1's, shackle flip, helper bags, and removed and readjusted coil overs I got her squatted on all 4 corners EQUALLY. I rub in front occasionally on full lock to drivers only and over excessive dips in road mostly in front. I have bumped coil over adjustment up 2 clicks from factory on drivers and 1 on passenger. I have compression up 2 clicks from middle and run helper bags with 8-10lbs in them when bed is not loaded up. Rarely do I ever bottom out these days, usually if I have the truck loaded up with people to hit work lunch.
       
      Sound System:
      I upgraded the sound system at some point in time between ICON's and slamming. This has been an ongoing mod debacle on my end. Started by building a steel rack behind passenger seat to mount three Memphis amps. I was using 3 Memphis amps I had from my old truck build, however the front amp decided to start sending unwarranted signals to the speakers and the rear amp after about 3 years of sitting and 6 months of using decided to finally die after an overall 10 year party in 3 different rides😒. None the less the two AB amps were replaced with new Memphis hardware while the class D (knock on wood) keeps trucking along. Doors received focal 3-Ways up front and 2-ways in the rear. Class D memphis runs a sundown 10 under the passenger ina  semi-custom box, added some height to the magnet area to accept the depth of the sundown 10 that runs on 1ohm. Memphis feeds it something like 800 watts rms @ 1ohm. Oldy but faithful Pioneer double din is running the show after trying 2 other setups to use the stock head unit. I initially tried pioneers CAN module but making fine tune adjustments or simply turning off the sub for when the kiddo is in the truck was a painful operation. Switched to an AXXES CAN setup, access to this was great, all the adjustments were perfectly accessible, however my trucks CAN did not like this system, I was getting all sorts of weird can signals and issues throughout the truck that I finally ripped that out and sent it back after trying two different AXXES units.
       
      Exterior:
      2nd year into ownership finally replaced the factory grill with the OEM paint matched honeycomb and updated the fogs and headlights with RIGIDs and paint matched 14-15 style headlights. Also threw in TRLS HID bulbs while I was at it and TRLS rear assembly's as well. I am an avid mountain biker so finding an easier way to load up the bikes was a must, when the pand hit I pulled the trigger on the RIDE88 truck bed system as they were doing a 25% off on preorders. Best investment for a biker ever, so easy to load and lock the bikes up, only painful when I have to fully utilize the bed.
       
      Performance:
      Stock 5.3, that is mostly clapped out, so I have not gone ham under the hood. Initial purchase was an air raid intake using the stock box as most factory units pull outside air vs "cold air" tech. So installed the AirRaid intake tube that ditches the sound deadening box and did a drop in oil filter. After much debate, about a years worth, I pulled the trigger on the MBRP side exit exhaust. I knew from the day I started the truck with it on that I absolutely HATED it but for some silly reason I left it on. Now I am in search of an OEM exhaust so I can throw this junk away and do an electric dump out later on down the road.  Eventually I will be swapping the 5.3 out for a LS1 or LS3 depending on what comes available next fall (waiting for prices to drop) and I will replace or rebuild the trans and will 100% replace the transfercase (culprit to my Chevy shakes when auto mode engaged) but first I need to finish my latest weekend warrior so I have a new daily while this ol'gurl is down.
       
      More to come
       
       
       









    • By Ronjon
      Does anyone have experience with belltech lift kits? I've seen plenty of positive reviews from their lowering kits. They've been in the suspension industry for a while, just not so much the trail or lift side.
       
      Long travel is the end goal, but a $700 coilover kit with a 5 yr warranty vs an extended strut sounds more functional.
       
      I'm considering the adjustable 3-4" lift coilovers, part #15203. 

      -Helper spring
      -60mm damper body
      -35mm independent valves
      -20mm piston rod
       
      I've got a 2020 z71 with the 3.0 Duramax for those needing an image to work with.
      Still exploring UCA options. 35*12.5r17 will be the tire size.
      Probably going to order them next month.
    • By Magoo11
      Got a 07 Silverado 1500 classic crew cab with the short bed 5.8ft. Need to replace my bed but having trouble finding another short bed. 
       
      does anyone know if I could put the regular 6ft bed on and will the wheel wheel/fuel filler neck, and bolts line up? 
       
      thank you 
    • By Addichevy
      Got my full console from Ebay used in like new condition. I did alot of research to figure out how to wire it so all the functions would work. I.e. wireless phone charger and  usb/ cigarette liter ports for the rear passenger.
      I have a currently have a 22 2.7l Custom that doesn't have the required connection under the front passenger seat. After hours of looking at schematics and testing wires, I managed to hard wire my center console to the fuse box on the passenger side.
       
      Wire on the CC harness to Fuse box
      Both Red/white to F5 (Battery positive)
      Violet to F20 (Accessory on)
      Violet/yellow to F23 (Accessory on)
      BOTH Black to Ground below the Fuse box.
       
       
      The only section I wasn't able to get working yet is the USB in the middle of the console (the one with the map SD card). This one I believe needs to be connected to the radio that has the built in navigation. (once I get one I'll update this post.


    • By stevenv76
      I have a 2007 1500 crew cab classic that I've done more restoration and customization to than I really would like to admit especially with guys that truely understand these trucks.  I went way to far because I needed a truck to haul more than mine should have done and refused to get rid of it.
        All that being said, my frame is rusted to the point that repairs are no longer going to cut it.  I've replaced 1 cross member, boxed in the back half with 10 gauge steel, added braces but now the cross member above back tank strap is rusted off drivers side as well as the large one under rear of the cab and it's trying to fold on me.  I've replaced all bushings on control arms, tierod holes modified to accept hd tierods, new CV axles, front diff gas new outter bearings and seals, new ujoints in front and rear shafts with the rear being a steel shaft that is rebalanced.  freshly build transfer case with pump guard, transmission has an upgraded trailblazer 2400 Stall converter so about 2700 in the heavier truck, input shaft for a 4l65e, redline wide bands, Corvette servo, 9 plate clutches and hd bearings.  the rear diff is a Yukon duragrip, swapped from 3.42 to 3.73, 4 wheel disk with drilled and slotted, gutted the cats with a 3" stainless mbrp  installers choice cat back single exhaust, ho premium tune. I also installed a 5000lb load/lift airbag system with pump and tank behind the rear seat and guage/controller in the dash.  body is completely redone after being tore down to the driveline and cab bring only thing left on the frame so I was already half way there 3 years ago. 
        The big question is what year frames can I use frame wise.  what will be the cheapest option in everyone's opinion?  living in northern Michigan, finding a used one local is kinda dumb in my opinion because you're going to be blasting a ton of rust off at 5he least so why go through the work of swapping with another. one that is already half way gone.  will either be driving to get one or having shipped.  somewhere between me and Arkansas would be best as I have a friend that makes that trip several times a year.  of course money is tight especially with this hog costing me 51¢ a mile in just fuel the last couple weeks.  I'm seriously leaning towards wanting to do a swap with a frame that has the harness attached still.  I'm having electrical issues from hell to boot.  gas gauge hasn't worked since 2018 when I got it and I've tried everything shy of ecm(I did try bcm and tcm), I've got a bad wire somewhere in harness for bank one and also to the tps.  I play with those. wiring harnesses if it starts to run bad and it smooths right out but have no clue which wire is to be the culprit and pinpoint the break inside the sheathing.  the biggest ****** there is 07 classic is a complete Frankenstein from the factory.  the engine is flex fuel capable but no active fuel management which all the fuel components are the same as 08.  the oil filter is ordered by 08 to make sure I get the right one.  suspension parts I just say 06 on.  half the all cab wiring is ob's so I don't know how this all plays out harness wise.
        I parked it under a big tree Thursday that had a ton of very large dead libs during a severe windstorm and nothing but a nice live tree did fall right where I had it parked prior and no I can't make this ****** up.  I'm over insured and was hoping for a little help with my decision on this thing.  
        sorry for the rambling guys, just wanted all factors to be known when advise given 
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    241.4k
    Total Topics
    1.4m
    Total Posts
  • Member Statistics

    305,255
    Total Members
    8,960
    Most Online
    R Y
    Newest Member
    R Y
    Joined


×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.