Jump to content

  • Sign up for FREE! Become a GM-Trucks.com Member Today!

    In 20 seconds you can become part of the worlds largest and oldest community discussing General Motors, Chevrolet and GMC branded pickups, crossovers, and SUVs. From buying research to owner support, join 1.5 MILLION GM Truck Enthusiasts every month who use GM-Trucks.com as a daily part of their ownership experience. 

Yukon Tahoe or Escalade spotted?

BenCash
 Share

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Content

    • Derick R
      2008 Yukon XL Drive train Issues.
      By Derick R
      Hello all I'm new to this read forums my entire life when needing help on a issue someone had back in 99. But anyway I have a 2008 Yukon xl 5.3 bought it a few years back quickly realized there was a issue on top of issue. I got screwed and screwed big time. Truck was sold as 168k miles. It was clean nice good looking truck for 4800 bucks. Turns out won't go over 65. We'll we just said screw it and run it for a while until we got our excursion. So now I've been trying to fix it. I need help I've tried refresh at the dealer it sat there for a entire day in a bay with a tech and they couldn't figure it out. So back to the drawing board. Later on tried to trade it in they pulled the carfax trunk our dude swapped the cluster and it was said the last reported mileage was 278k. Well ******. I want to figure out why it will not surpass 65. It has all the gears. Engine has all the power. No limp mode no codes. I have even pulled the cluster and drove it and that didn't change anything. Please help. Thank you. Derick r. 
    • Arvid Podsim
      MIL is illuminated with DTC P050D on a Cold Start
      By Arvid Podsim
      Reciently the Check Engine Lamp (MIL) came on at start and remainded on with no noticable engine running rough.  The error codes were read which indicated 400+ Cold Start error codes on Cylinder No.3.  Their are several GM Service Bulletins (PIP5498M, PIP5628E) on this subject V8 on engines from 2000-2022.  The bulletins indicate the "Cold Start" causes misfires due to coolant entering the at the liner to deck face casting or the casting line in the intake port of the cylinder head, in my case No. 3.  The GM Service bulletins indicate "engine replacement" is needed to fix this problem.  I have been very happy about this vehicle however, at 67K miles, this type of issue should NOT be occuring.  Apparently GM has know about this problem since 2000-2020 model years described on the attached Service Bulletins.
       
      After Two days of MIL being ON, the lamp is now OFF.  My question is how can the problem described repair itself and could the diagonistic codes be attributed to another problem?  I was under the impression that once the diagonistic code is initiated, the only method of turning OFF the MIL is by resetting or clearing the codes.
      PIP5498M.pdf PIP5498M.pdf
    • Snake River Wraps
      2004 yukon denali xl caliper replacement
      By Snake River Wraps
      2004 Yukon Denali XL 1500 AWD
      Ok, so I have done many brakes in the past but this has me stumped. I put new calipers rotors and pads all the way around on the truck and have bled the brakes like 6 times. twice with a helper and 4 times with a bottle. All times the fluid comes out with no air but it still goes to the floor when its turned on. A small amount of push back is noticed after pumping a few times while the truck is off. But as soon as I turn it on and push its nothing. I have read about there possibly being air in the ABS module and am looking for how to bleed that with just one person and have it actually work. The master cylinder is and has been filled throughout and never dropper too low. I placed all the new parts and puller the hose off the old calipers and attached it to the new ones quickly replacing the copper washers. I just cant figure out what could be happening, any help would be appreciated.
    • ABallard
      1999 1500 Interior update
      By ABallard
      I'm looking to do a full interior swap/update on my '99 silverado, don't know much about interior fabrication but i'm going to do what I have to in order to make it work. For now I plan on taking everything I can out of a part-out silverado from 2014 or newer and throwing it straight into my truck. If anybody has any tips or prior knowledge from a project of the same nature any help would be appreciated. From what I could find, not many people have documented this sort of thing on YouTube and the ones who have only show off the final product instead of the full process or steps they needed to take in order to get what I'm looking for. 

    • GMjarrett
      2015 Yukon Denali magnetic ride failure
      By GMjarrett
      I recently purchased a rebuilt title Yukon, comes with the magnetic ride. The ride is extremely rough, to the point where I’m assuming the system is just not operating. I’m not getting a message on the display for anything, unless the parking sensors and lane change sensors not working have something to do with it. The previous owner said he installed a 2” level kit to help the ride. At the time I didn’t understand what he was talking about. But anyone with any information or previous experience that could spread some knowledge, I would be thankful. 

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    242.1k
    Total Topics
    1.4m
    Total Posts

  • Member Statistics

    309,758
    Total Members
    8,960
    Most Online
    Oscar126947
    Newest Member
    Oscar126947
    Joined


×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept