Search the Community
Showing results for tags 'sway'.
Found 4 results
Hello all, I have a 2015 GMC Sierra 1500 Denali 4WD and I would like to install some Timbren bumper stops. On their website there are 3 different kits for the rear: 1. Regular Suspension 2. Magnetic Ride suspension and, 3. Adaptive Suspension I came across an article stating that the my truck has the Magnetic Ride suspension but I need someone to confirm the fact. Also if anyone else installed these kind of bumpers can you please share the part number that would fit to this specific model of GMC? Thank you.
Hello, I have been helped by various posts on this forum for a long time but now joined mainly to ask some questions about upgrading my van. Here is the scenario; my dad purchased the 2000 Chevy Express Conversion Van new from a dealership back in 2001. We used it as a family vehicle for many years but as us 'kids' grew up and married off, the van was left unused. So I purchased it from my dad and have been fixing it up. Whoever did the conversion was an idiot. They took an Express 1500 and made it into a conversion van that weighs 6,800# empty. *The front doors are so heavy we had to reweld the hinges because the factory spot welds were peeling off. *The van had front DRUM brakes which we changed out for a set of Brembo slotted disk brakes. *Changed rear axle ratio from whatever stock was down to 3:73 *I upgraded the wheels from 15" to 17" and the tire size from 26" to 30.5" (yes the front tires rub sometimes, but it is 10X better in snow and rides better.). *I replaced the rear leaf springs with 3/4 ton leaf springs and coil-over heavy duty shocks. *Upgraded the full exhaust system from the manifolds back with 3" pipe and a high flow cat and Thrush muffler. *Replaced the engine after I was a dumbA$$ and never refilled the coolant with coolant after having to add water due to a leak and the block froze and cracked. The replacement engine was taken from a 1999 Chevy Suburban. *The transmission was replaced with a Monster Transmission brand 4L60-E rated up to 600hp and tuned for towing (quick firm shifts) and a heavy duty torque converter. *Replaced all ball-joints and steering bushings. *New "heavy duty" shocks for front suspension - which didn't change anything like I was hoping. Anyway, now I want to upgrade the front suspension because it is SO SOFT that the van struggles to ride flat if the road has any bumps in it. It is 2WD, so no front axle. 1: I want to upgrade the front and rear sway bars, can I just put 3/4-ton or 1-ton sway bars on it? Will they fit? 2: I want to upgrade the front springs and shocks with 3/4 ton springs and shocks. Is this possible? 2b: I would also be happy if anyone new of an air suspension or air-adjustable shocks that might work as well. I can't seem to find anything for front suspension for 2wd Chevy vans or trucks. Thanks for any help.
Hello How it going? I wanted post and ask some questions as along the way and see if I am crazy enough to upgrade and discuss about modifying a stock GMC 2016 4x4 2500HD 6.0L Gas suspension system. The truck needed a nice smooth riding stability control system on it's suspension system and along it needed to takes more weight load carrying capacity controls from major loads when towing big loads from over hauling trailers. Plus even on it's no-loads capacity as well when you need to drive on a everyday needs in all conditions from all driving ability and keep safe from going out of control from all major issues on the roads conditions on a stock 2500HD/3500HD, I can tell things are getting out of control as conditions are getting worsts beyond our controls when dealing with a stock HD trucks suspension system on a bad roads conditions. Anyway I wanted to upgrade this truck to improve the truck without spending to much money but enough for the truck to drive better than possible so here some ideas and list of parts of modifications that I have studied and thought about thought I post something asked and shared and discuss as asking some ideas for some upgrades. Thanks for helping guys as I need some helps. So far I already installed a rear Hellwig Big Wig Sway bar the model # is 7270 and have it on the medium setting on the links holes for the sway bars as it on the #2 holes. The center hole is considered is medium setting. The far out as #1 hole is the lose setting and far back to the axle #3 hole is tighter setting for the sway bar settings. And I have to say I already feel a huge improvements to the rear suspension by adding a rear sway bar. I can tell by it does prevents the waving as rocking side to side when driving into a drive ways or pulling into a intersections or running over pot holes or curbs or jumping over a railways or hills and some major improvements on things like those quadruple humps and ripples as dips on the road that make your whole truck shake everywhere and wobbling back and forth from going over on those melted asphalt from the roads and highways as it swerves out of control at a high speed and including hauling something that makes it bounce everywhere even to lose control on a empty bed. Plus the improvements over driving into by turning fast and pilling out or in front of the traffic as keeping the truck lock down on the road to pull in and it enforce it from leaning over, keeping the truck from waving over as swerving out of control from rocking by it side. And the sway bar does improve towing. It help you to control your trailer from losing out of control from a dodge moments on cars and winds and other moments to prevent your trailer from wobbling on a highways. Keep the back end stable as twisting the roll body of the truck especially pillingout on a burn out. it been been lot of flooding in Texas lately and I need to spray paint it black and painted the u bolts as well as keeping it from rusting including the axle drive staff joint. Rust is a disease to metal. I only have this 3 months of use of this Hellwig and this truck has 9,786 miles on it. Now the questions is do I needed to go ahead and buy the front sway bar? And put a bigger heavier duty links as well that hooks on to the front sway bars? I don't know what size the is the original stock front sway bars as in inches from as American scale, so far, I founded out the size it is 1.250 of a inch? Is that 1 inch and 3/8 in size? or is that 1 and half of a inch? And the links that came with the truck looks little poor. Looks like it needed to be on a 1500 models trucks and asking for a bigger set of links to control the front of the sway bars on the 2500HD front end suspension. But anyway the Hellwig has a 1 and 1/2 of a inch in thickness of the sway bar and if the the truck stock sway bars is the same size then I don't need to get it it be a waste of money by having the same size bars. I don't know if that make anything big of a different but maybe it will in tightness of a sway bars as for front suspension system if it little bigger right? Anyway here are the list of the modifications upgrades for the suspension system packages that are listed for a smooth ride with major medium payloads capability. Feel free to post some idea of some more modifications suspension system for a stock GMC /Chevy 4x4 2500HD / 3500HD 2014 to 2019. Hellwig Rear Sway Bar 7270.......Weight: 8,000lbs Hellwig Front Sway Bar 7716......Weight: 5,000lbs Hellwig Leaf Helper Springs Stabilizer LP-3512.....Weight: 3500lbs Leaf Spring Shocks Absorbed Sulastic Shackle For Axle SA-06...Non-affect load carrying capacity BDS NX2 Single Steering Stabilizer with Mounting Bracket Kit.....Get Boot Cover Protection PPE Stage 3 Tie Rod Assemblies #158031511.....Has Larger Ball Joints and Staff SuperSpring Front Sumo Spring SSF-202-54......Weight: 2000lbs SuperSpring Rear Sumo Spring SSR-203-40-2....Weight: 2600lbs Max at 80% 3000lbs G2 GM 10.5" 14 Bolt Rear Brute Ball Milled Aluminum Differential Axle Cover.....Amsoil 95W-140 Gear Oil Fox Shocks 2.5 Reservoir Front and Rear. These are my upgrades for a medium high performance stabilizer for the truck suspension system modifications. As for tires and rims I would love to have a 20 inch rims with 285/65/20 tires Or 18 inch rims with 285/70/18 tires one day. This should improves the overalls of the trucks capability right? Dream engine on this truck is LS1 427 32V 6.2L 25MPG on this 2500HD 4.10 gear ratio with the twin as y air filter intake system with dual exhaust .... Goals <3.. I wish I could afford this and to put a 8 speed tranny on it.
Hi all, I haven't posted too many times in the forum... but I have found another question and would like to hear some opinions. I am in the market for a new travel trailer. I have found the newer models are significantly lighter than my current camper. I am currently pulling a 32' travel trailer that weighs in (on the scale) just over 7,000lbs. Being an older trailer, I just don't think it hauls well... (and I will be honest, I have it a little nose down- my mistake when setting up the WDH.) I hate driving this on the highway, I prefer slower state roads that don't face big rigs passing by, winds that blow you around, and generally just feel more in control on them. On the highway, I feel I need to drive slower 55-60 and still keep a hand on the trailer brake. I have also noticed on newer campers they have begun spreading the axels a little farther apart (more stable?). I am trying to figure out if I need to step down in both weight and length to get a better towing experience, or simply lowering the weight (and correct WDH setup) will improve the tow-ability... Will a light but long trailer get blown all over the road? My truck details are copied below from another post; I am well within weight limits for my truck (@7,700lbs). I would like to be able to travel at normal highway speeds- 70-75) and feel comfortable... The hard part is finding a camper with the features we (my wife) wants that will tow comfortably. Suggestions are welcome here too! Bunk Beds, One or Two entry (if one it cannot be next to bunks), sofa, slide out for floor space, queen bed separated by wall... thats not too much to ask is it? (jk- its tough to find without hitting 30'+) If a manufacturer would just make a model with a sofa instead of a slide out dinette we would be sold! *2012 GMC Sierra 1500. Specs on the truck include; 4x4, crew cab, max trailer package (5.3 KDL HD Cooling Package, trailer brake harness, 3.42 ratio). I have installed the Tekonsha P3 brake controller. I currently have the Camco Recurve R6 hitch for sway and WD. The truck manual max trailer weight states 9,500lbs with a GCWR of 15,000lbs (truck GVWR 7,000lbs). I do understand the balancing required between truck and trailer for GCWR; if truck fully loaded is 5,500lbs and tongue weight is 1,000 pounds the max trailer becomes 8,500 pounds not the book stated 9,500. I am thinking a 7,700lbs GVWR for a trailer will fall WELL within specs. I also plan to add SumoSprings to my truck later this spring- and possibly stronger tires on the truck for towing...