jimbowattz

Decided to sell my Chassis Unlimited Octane front bumper. I ran with this for approximately two years while living in SoCal but have since relocated to Orlando. It's a solid bumper that is very low-profile and doesn't stick out in front very far like most other off road bumpers do. It also has the parking sensor cutouts which is an additional charge from the manufacturer, but I'm keeping my sensors. So you'll need to swap yours over from you current bumper. I'm also including 4 KC HiLites C-series light pods, and a 30 inch Rough Country black series light bar. I don't have the full lengths of the wires that connect the lights to a switch, but I typically cut those off and wire up my own wires anyways. If needed, you can buy them from KC and Rough Country. Minor wear marks in a couple places from the California deserts and mountains, but nothing serious. The biggest mark is on the top of the bumper where the grill rests on the top. There's a light rust mark that can be hit with a quick mist of spray paint if it bothers you, or is fine to be left. It can't be seen once mounted as the grill rests on top of this spot. - Chassis Unlimited Octane Series front bumper - Black powder coated - Parking sensor cutouts - (x4) KC HiLites C-series light pods, amber beam - Rough Country Black Series LED light bar, single row, 30 inches

Check out Dirt King Sent from my SM-G973U using Tapatalk

I don't notice a difference in ride between ring 2 and 4. Both ride great. Worthwhile upgrade, very happy with them so far. Sent from my SM-G973U using Tapatalk

They were indeed set to the second ring instead of top ring. Below is after the correction. 5100s on #4 with 2" blocks. Looks much better IMO. Included old photo as well for comparison. Sent from my SM-G973U using Tapatalk

Ok, so the first attempt did indeed only set the height at the second ring. Just moved it to top ring today. Fixed my problem. First pic is the 5100s on ring #2 with 2" rear blocks. Second pic is ring #4 in front with same 2" block. Sent from my SM-G973U using Tapatalk

Cool thanks Sent from my SM-G973U using Tapatalk

Is my brake cable routed incorrectly? Seems to be hanging down below the axle, and I don't recall how it was routed prior to the rear install. Sent from my SM-G973U using Tapatalk

Did you add an inch in the rear as well or stock block? Edit: never mind. Saw your post in the other thread. Looks good. I'm hoping that after I get the ring adjusted next week my 5100s match the slight rake you have in your after pics. Sent from my SM-G973U using Tapatalk

Does anyone have any video or audio of the sound? Curious if it's what I hear occasionally under slow acceleration. Sent from my SM-G973U using Tapatalk

For sure, I'll post up new after pictures once fixed. Getting them adjusted on Monday. Thanks all. Sent from my SM-G973U using Tapatalk

Looks like they didn't install on highest ring. This is either lowest or second lowest. Fixing this weekend. Once fixed I'm expecting to be around 1.5 inches if rake or so. Sent from my SM-G973U using Tapatalk

Thanks, will do. Starting to think my guy messed up... I should have measured before hand... Sent from my SM-G973U using Tapatalk

Ok so I effed up with prior measurement. Parked her flat and here's what I got. Have 3 inches of rake. Ring looks to be on top setting. What am I missing? Sent from my SM-G973U using Tapatalk

I'm pretty sure it's highest setting, but I didn't install the fronts. But I asked shop twice to confirm and they said highest. Just tried to look under truck but it's hard to tell which ring with the boot covering the top. Sent from my SM-G973U using Tapatalk

Posted these in the Bilstein thread, but will leave them here as well I suppose. 2018 6.2L Z71 Midnight with the 8spd trans. Sent from my SM-G973U using Tapatalk

Yes, stock wheels and tires on the midnight edition. 1.5 inches higher in rear than front. Anyone know what stock rake is? I figure I would have been within a half inch of being level using highest setting had I not changed the block. Again I'm fine with rake, just not more than stock. Sent from my SM-G973U using Tapatalk

Installed Bilstein 5100s in front/rear with 2 inch block in back. Fronts are at highest setting. Still too much rake? I wanted to keep some rake but don't want more than factory. Failed to take picture prior to install unfortunately so I don't recall how much rake it had before. What do y'all think? Sent from my SM-G973U using Tapatalk

Installed Bilstein 5100s in front/rear with 2 inch block in back. Fronts are at highest setting. I think it still has too much rake. I wanted to keep some rake but don't want more than factory. Looks like I'll be raising up the front a little more somehow I suspect. Sent from my SM-G973U using Tapatalk