Search the Community

I have a 2007 1500 crew cab classic that I've done more restoration and customization to than I really would like to admit especially with guys that truely understand these trucks. I went way to far because I needed a truck to haul more than mine should have done and refused to get rid of it. All that being said, my frame is rusted to the point that repairs are no longer going to cut it. I've replaced 1 cross member, boxed in the back half with 10 gauge steel, added braces but now the cross member above back tank strap is rusted off drivers side as well as the large one under rear of the cab and it's trying to fold on me. I've replaced all bushings on control arms, tierod holes modified to accept hd tierods, new CV axles, front diff gas new outter bearings and seals, new ujoints in front and rear shafts with the rear being a steel shaft that is rebalanced. freshly build transfer case with pump guard, transmission has an upgraded trailblazer 2400 Stall converter so about 2700 in the heavier truck, input shaft for a 4l65e, redline wide bands, Corvette servo, 9 plate clutches and hd bearings. the rear diff is a Yukon duragrip, swapped from 3.42 to 3.73, 4 wheel disk with drilled and slotted, gutted the cats with a 3" stainless mbrp installers choice cat back single exhaust, ho premium tune. I also installed a 5000lb load/lift airbag system with pump and tank behind the rear seat and guage/controller in the dash. body is completely redone after being tore down to the driveline and cab bring only thing left on the frame so I was already half way there 3 years ago. The big question is what year frames can I use frame wise. what will be the cheapest option in everyone's opinion? living in northern Michigan, finding a used one local is kinda dumb in my opinion because you're going to be blasting a ton of rust off at 5he least so why go through the work of swapping with another. one that is already half way gone. will either be driving to get one or having shipped. somewhere between me and Arkansas would be best as I have a friend that makes that trip several times a year. of course money is tight especially with this hog costing me 51¢ a mile in just fuel the last couple weeks. I'm seriously leaning towards wanting to do a swap with a frame that has the harness attached still. I'm having electrical issues from hell to boot. gas gauge hasn't worked since 2018 when I got it and I've tried everything shy of ecm(I did try bcm and tcm), I've got a bad wire somewhere in harness for bank one and also to the tps. I play with those. wiring harnesses if it starts to run bad and it smooths right out but have no clue which wire is to be the culprit and pinpoint the break inside the sheathing. the biggest ****** there is 07 classic is a complete Frankenstein from the factory. the engine is flex fuel capable but no active fuel management which all the fuel components are the same as 08. the oil filter is ordered by 08 to make sure I get the right one. suspension parts I just say 06 on. half the all cab wiring is ob's so I don't know how this all plays out harness wise. I parked it under a big tree Thursday that had a ton of very large dead libs during a severe windstorm and nothing but a nice live tree did fall right where I had it parked prior and no I can't make this ****** up. I'm over insured and was hoping for a little help with my decision on this thing. sorry for the rambling guys, just wanted all factors to be known when advise given

I NEED HELP PLZ. I have a 2014 Silverado and a car or truck hit me while I was in a store parking lot today. I have found a 2019 fender and it looks close over pics but I don't know for sure if it will fit. Please if anyone knows the answer it would help greatly and save me some money!! I would have reported it but don't want it on my trucks history. Can someone give me info or may have what I'm looking for the truck is red if wondering. Ty god bless everyone during these horrible times.