Jump to content

David solar

Member
  • Content Count

    30
  • Joined

  • Last visited

Community Reputation

32 Good

About David solar

  • Rank
    Enthusiast
  • Birthday May 24

Profile Information

  • Name
    David Solar
  • Location
    Ellijay ga
  • Drives
    2014 gmc sierra

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Thanks man I will do that and my biggest issue is the truck is always and I means always Reving up in the rpms to move like jumping the Rpms it will never just cruise and I can give it a little without it jumping in rpms to try to move Sent from my iPhone using Tapatalk
  2. I know I’m not going to break even with this but this is the truck I could afford at the time and now I’ve got it so close to being payed off it it would be stupid to get rid of it I’m gonna run it till it blows Sent from my iPhone using Tapatalk
  3. Thanks man and yeah the v6 isn’t bad but it just can’t handle those tires at high speed and hold It the tuner did help a ton I noticed a big difference Sent from my iPhone using Tapatalk
  4. My problem is that motor I’m just trying to find ways to get it back to how it was so you would go with 4.56 gears? Sent from my iPhone using Tapatalk
  5. Hey guys I’ve got a 2014 GMC Sierra 2wd 4.3 v6 on a 7inch lift 22x12s and 35s the trucks got 3.23 gears in it and when I bumped up to 35s from 33s it seems like it is always constantly searching for gears on the Highway or above 50mph I get around 13 mpg and I would like to retain that or get better if possible and I’m trying to decide wether regearing the truck would be worth the money and also what gears to go to If I get it done if 3.73 or 4.10s would be better I would like to retain as much gas mileage as possible but not have the truck struggling 24/7 when it hits a hill it just sucks the
  6. It’s a magnaflow y pipe I got it for like 35 bucks Sent from my iPhone using Tapatalk
  7. I used the stock mounting brackets that came with the light and grinded a little off the edge it’s a perfect fit
  8. Just got my n-fab steps put on yesterday I love the way they look on the truck Sent from my iPhone using Tapatalk
  9. Thanks it’s taken a while to build it it’s my first truck but I honestly don’t know if your gonna be able to clear with a 2 inch leveling kit I am stupid close to rubbing but I Cognito control arms so helps there Sent from my iPhone using Tapatalk
  10. 3 inch Motofab Leveling Kit stock blocks in the rear I installed it myself but my wheels are -51 offset so they sit out a little more but with the NorCal I undid everything pulled the liner back then cut the pinch weld out cut the corner of the bottom inner corner but make sure to leave the hole on the bottom for the bolt than cut the felt than beat in with a hammer the inner fender till it’s flush with the back panel than sprayed it with rust resistant black paint and trim some of the fender flare thing I have no rubbing at all but it’s super close tho I’ll get more pics soon The hammering p
  11. Yeah I had to grind a little off the tabs for the mounts but drilled a hole for the wire passed it through and t-taped it into my fog light wires so when I turn on my fog lights it come on and when my I turn on high beams it comes on with my fog lights it’s really sleek and made it look better in the front Sent from my iPhone using Tapatalk
  12. It works amazing and it’s just a xprite 20 inch slim light bar off amazing for about 70$ that’s before my hids and fog lights so just halogens and light bar Sent from my iPhone using Tapatalk
  13. 20x12 -51 vision rockers on 33x12.50 Federal Couragia Mt 3 inch Motofab Leveling Kit stock blocks in the rear It rubs so bad but did a NorCal mod on one side and I ran out of daylight gotta do the other side tomorrow ? but after the NorCal it doesn’t rub at all Sent from my iPhone using Tapatalk
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.