Jump to content


  • Content count

  • Joined

  • Last visited

Everything posted by ChevyTech007

  1. Problems With Odometer/trip/hr Meter

    Subject: Information on How to Change IPC/DIC Language - keywords cluster display English French IPC Spanish trip #PIT3404A - (07/25/2006) Models: 2003-2006 Cadillac Escalade Models 2003-2006 Chevrolet Avalanche, Suburban, Tahoe 2003-2007 Chevrolet Silverado Classic 2003-2007 GMC Sierra Classic 2003-2006 GMC Yukon, Yukon XL, Yukon Denali Models -------------------------------------------------------------------------------- This PI has been revised to add additional model years. Please discard PIT3404. -------------------------------------------------------------------------------- The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern: Starting in model year 2003, the IPC/DIC is able to read out in 3 difference languages: English, Spanish, and French. Some questions have been received concerning how to change the DIC Language, mainly on vehicles without steering wheel controls. Recommendation/Instructions: To change between the languages on vehicles with steering wheel controls, follow Document ID # 867116 in SI. Vehicles without steering wheel controls follow the procedure below: Turn ignition on. Use the trip rest stem to display the Odometer on the DIC. With the Odometer displayed press and hold down the trip reset stem, after 3-5 seconds the DIC will begin to scroll thru the 3 difference languages. Continue to hold down the trip reset stem until the desired language is displayed then release the trip reset stem. Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.
  2. Found this. It might apply. Subject: Unwanted/Loose Seat Movement (Apply Adhesive and Install New Bolts in Seat Mounting Rails) #05-08-50-012 - (10/06/2005) Models: 2002-2005 Cadillac Escalade, Escalade EXT 2003-2005 Cadillac ESV 1999-2005 Chevrolet Silverado Pickup Models 2000-2005 Chevrolet Suburban, Tahoe 2002-2005 Chevrolet Avalanche 1999-2005 GMC Sierra Pickup Models 2000-2005 GMC Yukon, Yukon XL 2003-2005 HUMMER H2 with Power Driver Front Seat Power Adjuster (RPO AG1) and/or Passenger Seat Power Adjuster (RPO AG2) -------------------------------------------------------------------------------- Condition Some customers may comment on unwanted seat movement in the front power bucket seat (driver or passenger) during fast acceleration or hard braking. A metal to metal clicking noise is often heard at seat "stops." Cause The threads of the two zinc nut retainers (one on each side of the seat adjuster) may creep over time, causing a loss of self-rolling screw clamp load and ultimately causes relative rail and vehicle seat motion. Correction Apply adhesive and install new bolts in seat mounting rails using the following procedure. Remove the front seat and invert onto a flat surface covered with a clean, non-scratch material (soft cloth or similar). Refer to the applicable Seats sub-section in SI. Adjust so that the seat mounting rails are at 45 degrees. Remove the upper M8 mounting bolt from one rail and discard. Leave the other bolt intact as this will hold the track in place while working. Wipe the bolt hole area with a clean rag. Important: Only use the adhesive provided in the repair kit. Do not substitute with other adhesives. Take one of the adhesive sachets and carefully cut the flag tip off the notched end spout in line with the notch. While holding the sachet vertical, slowly dribble the adhesive into the edge of the bolt hole as shown, ensuring that the adhesive flows into the joint between the seat rail and the zinc block. DO NOT pour the adhesive down the center of the hole. The object is to let the adhesive "wick" between the zinc block and the seat rail in order to bond the two pieces together. Important: If the bolt thread strips or the proper torque cannot be achieved, then the entire seat adjuster mechanism must be replaced. Replace the previous bolt with a new M8 bolt (1) (included) and install using a "click torque wrench" preset to 9 N·m (79 lb in). Remove the second M8 mounting bolt from the rail and discard. Repeat steps 2 through 5 for the second bolt. Repeat steps 2 through 6 for the opposite mounting rail. Before installing the seat into the vehicle, verify that the seat will function correctly and does not make any unusual noises during forward and rearward travel motion. Install the seat. Refer to the applicable Seats sub-section of SI. While sitting in the seat, verify seat function and listen for any unusual noises. Parts Information Part Number Description Qty 89045784 Adhesive Kit, D/Seat Adj Bolt 1 kit per seat

Important Information

By using this site, you agree to our Terms of Use.