Search the Community
Showing results for tags 'broke'.
Found 4 results
I have found the FIX for broken rear camera cables. I broke my rear trailer camera and was able to replace the connector with a new connector setup. Works well and if your handy you can do it yourself for under 40 bucks!!! Contact me for parts and cost information… email [email protected]
OK everyone I want to give thanks ahead for any advice and help. Truck in question= 2003 Chevy Suburban Z71, 5.3 L Transmission= 4L60-E So the story started when I was going down the road at about 50mph in cruise control, when suddenly I heard the engine begin to rev up. I hit the brake to take it out of cruise control and the engine stopped revving up. Apparently I lost transmission of power from the engine to the wheels because no matter what gear I put it into now, I get no movement from the vehicle. No reverse and no D1, 2 or 3. When I put the vehicle in park and attempt to push the vehicle it will not roll. When placed in any other gear I can then roll the vehicle freely. Before this happened: Since owning the vehicle 4x4 has always been shifty.....hehehe...sorry couldnt help it. I have the model where there are 4 buttons with lights the buttons are located left hand of dash near the turn signal. When I first got the truck sometimes it seemed like it didnt want to switch between gears. for example I would have to hit the button multiple times before it would switch and even then it seemed like it hadnt really switched but the lights would indicate it had. Most of the time the light for the button I selected would flash multiple times and then return to previous selection. Often times after turning the vehicle off and then returning to vehicle to go somewhere I would find that the light has switched back to a gear that it wasnt in when i left the vehicle. It seems to favor 4x4hi. As of lately I havent been able to get the lights to switch at all. It seems to be stuck in 4hi permanently. I have tested the 4wd switch and its fine. I tried unhooking battery for half hour with lights on to reset PC. I then reconnected battery cable and turned vehicle on but not start it. Then I pulled a bunch of fuses and plugged them back in. ( seen it in a video and the guy said it was supposed to wake up the TCCM) Well that did nothing. I have the truck off of all wheels right now and was trying to figure out if the transfer case is stuck in neutral. With the truck in drive as I turn the rear draft the front moves also. I am assuming that means it is in 4wd. But should I have someone hold the front drive shaft while i turn the rear drive shaft to confirm its not just from friction or something. I actually have the front drive shaft partly out right now in an attempt to get at and remove the shift motor and manually put the transfer case into 2hi. I am also considering changing out solenoids. I have gathered it is unlikely the shift solenoids. Is it possible it could be one of these: 1 * EPC (Pressure Control) Solenoid 1 * PWM Solenoid 1 * Manifold Pressure Switch 1 * TCC Solenoid w/Harness Another thing I suspect which would be an easy fix is the transfer case fluid level. I removed the fill plug and nothing came out. I can tell it has been leaking. I would have already topped it off but I have been stuck at home (no running vehicle lol). Could low fluid cause this issue? I hope that's all it is lol. Anyways I got a ride to the store tomorrow and to look at a back-up vehicle. Anything you guys recommend to grab from the parts store while I'm in town tomorrow? What would be your guys recommendation on how to solve this problem and fix it? All help is appreciated. thanks in advance, Aaron
hello everyone I have a 97 GMC Sierra with a 305 and electronic shift trans it has a lot of issues that I'm trying to sort out first of all on cold start it idles super low (200- 400 rpms) for a few seconds and then picks up and shudders and shakes for a minuet then goes to normal idle once it warms up it stars to drop to low rpms (any where between 100 to 400) and dies out when I rev it it revs super slow and hesitates when I go to drive it it falls on its face on take off it kinda cuts out at first but slowly and I mean slowly picks up speed all the while it back fires and slightly lunges now once I get moving the trans doesnt want to shift until I let off the gas no matter the throttle position and the speedometer jumps around like crazy and never shows my correct speed the brake and ABS light are on sometimes they go off but normally on look at the videos to see how bad it is any help would be great so far I have replaced the plugs and wires cleaned the cap replaced the button and the TPS cleaned the MAF sensor and cleaned the trans speed sensor videos:
97 chevy c 1500
Bambam2806 posted a topic in 1988-1999 Chevrolet & GMC C/K GMT400 Platformhi, i have a 97 chevy c1500 4.3 vortex v6 that was given to me. It had sat for about a year and a half before i picked it up. When i received it i put a new fuel pump and filter cleaned out the gas tank. It ran fine for 2 or 3 days and i drove 45 miles and it run fine. one day i drove it about 20 miles and it stalled, immediately when it started it would go then cut out again you couldn't go 50 ft without it losing power. The next day i changed the tps then cleaned the aic helped slightly but not much. Well come to find out my catalytic converter was blowing out honeycomb so we replaced it with a muffler since the real muffler had been cut (and no not directly under the truck we piped it out then put the muffler under the bed). It will idle but still wont run correctly i have heard there might be 2 fuel filters i will check that tomorrow. i will also ohm the 02 sensors to make sure the are working properly but they appear to be fine. Can anyone help me?