jcfountain33

$250 shipped conus

$275 shipped conus

Like New - Bora 1.25 inch Wheel Spacers for 14-23 Silverado/ Sierra 1500, 6x139.7 bolt pattern, 78.1mm hub bore, hub centric. On the truck less than a month. Had some rubbing and didn't want to add a level or trim the mud flaps. No trades. SOLD

Go to the tire manufacturer's website and check their specs, they should have a recommended wheel width for the tire size. Will depend on the shop whether or not they will follow the "recommendation". Some shops are strict about it, because of legal reasons, and some aren't, as it's a "recommendation". Sent from my SM-G970U using Tapatalk

It is probably safe, but when I tried to do it with Yokahama Parada Spec-X on my 9.5" Black Rhino wheels, Discount Tire would not install them because the Yokahama's minimum wheel width for that tire was 10". Pretty sure the Nitto 420 was the same. Move to a 20" diameter and 305's are fine. Sent from my SM-G970U using Tapatalk

Shackles and block removal was dead level on my 17 crew cab. Was within 0.25" at all 4 fenders. Sent from my Pixel using Tapatalk

For me, the biggest advantage of the spacer is it was that much less distance you had to tighten down the bolts. I didn't have access to air tools and was doing it by hand so would've taken a lot longer to tighten down the nuts, lol. Sent from my Pixel using Tapatalk

Not for 3", I've had no issues. Actually rides better than stock to me. I don't pull a trailer or haul anything though. Sent from my Pixel using Tapatalk

The block isn't rubber, it's steel and nothing to cut. McGaugheys and Belltech shackles are exactly the same. You could relocate the block to avoid needing spacers, but not sure what that involves. May have iterference with the spring stud. Sent from my Pixel using Tapatalk

Belltech kit comes with spacers, I think it's part #6401. I have a 17 crew cab and it dropped mine exactly 3". My 14 crew cab only dropped 1.75" with 2" shackles. The block b/w the axle and springs is 1.25". Fender height on my 17 is within less than 1/4" all the way around. Sent from my Pixel using Tapatalk

Yes, you have to drop the hitch, but that's not a modification... Sent from my Pixel using Tapatalk

Bend the bed seam over above the shackles to get clearance. Sent from my Pixel using Tapatalk

2" is the shackles, 3" is shackles and block removed. The 6401 kit comes with spacers so you can use the original U-bolts after blocks are removed. Sent from my Pixel using Tapatalk

I did the Belltech 6401 kit, shackles and nut spacers for removing the block and I'm perfectly level, within ⅛" all the way around, on my 17 Crew Cab LT. Rides great, no issues, with stick size tires. Sent from my Pixel using Tapatalk

I have the bell tech rear shackle with the block removed and rides no different than stock. Springs are the same, just slightly different attachment point. Not low enough to bottom out. Sent from my Pixel using Tapatalk

Belltech 6401 includes 2" shackles and spacers which allow you to use your existing U-bolts. On my 2017 Silverado Crew LT, fender to ground measurements are within 1/4" all the way around. I don't have pics on this phone, will try to find them to post. Sent from my Pixel using Tapatalk

I haven't changed the shocks and haven't had any issues. Sent from my Pixel using Tapatalk

Rush hour traffic in Atlanta getting on the freeway, any witness was gone 5 seconds later. Damage is on the front of her car and the side of mine, she says I turned into her. Physically no way that can happen, can only hope the adjuster can prove it. Trying to get traffic cam footage or statement from fire rescue unit as to the location of the vehicles before they had us move out of traffic, but officer hasn't called me back. Adjuster said all that has to go through the officer, so I doubt it'll get anywhere. Sent from my Pixel using Tapatalk

Finally washed mine today. Weather has been crazy and getting an additional pollen season. Was covered in pollen before I could even get it dry. Wasn't really feeling up to washing it since I got in a little fender bender a couple weeks ago, but wanted to see how bad the damage really was. 2 lanes turning left and the girl in the lane to the left of me decided to go straight instead of left, she was in the left turn only lane. T-boned my left rear, then lied to the officer and said I turned down into her. Now it's a he said, she said and we both get dinged on our insurance... Sent from my Pixel using Tapatalk

Blocks/shackles is 3", you lower it that much under load or when towing. If that causes a pinion angle problem there is an issue. No problem with mine... Sent from my Pixel using Tapatalk

I have the Bell Tech 6401 kit, shackles and U-bolt nut spacers for removing the blocks and have no vibration or ride quality issues. No pinion angle shims. Sent from my Pixel using Tapatalk

I did Bell Tech shackles and removed the block in the rear (used the Bell Tech spacers for the U-bolt nuts) on my 17 Silverado LT and it's within 1/4" all the way around. The blocks are 1-1/4". U thought was gonna be lower in the back but it wasn't. Front and rear are a touch higher on the passenger side. Sent from my Pixel using Tapatalk

Thanks, Silverado and LT are gone from the tailgate and Silverado will be gone from the doors as soon as it warms up. Want to match the bumpers/grille, but trying to figure out the best way. Sent from my Pixel using Tapatalk

22x9.5, love them, had a couple sets of black rhinos. Prefer something simple. Sent from my Pixel using Tapatalk

I have Black Rhino Traverse with 25mm offset so it sounds like I'll be trying the 305's when I need tires again. Sent from my Pixel using Tapatalk