Jump to content

brianc636

Member
  • Posts

    193
  • Joined

  • Last visited

Everything posted by brianc636

  1. I have it at home in the truck. I’ll snap a pic when I get home tonight.
  2. 3 months? Mine was 4 I believe at the same rate. At the end of the day though, they can’t come back after you if you re-fi early because it’s not a commercial loan and those terms aren’t written into the contract. How long before your truck shows up?
  3. Dropped the truck off today to get this and the brake pad issue looked at. The rear camera module needs to be replaced and they didn’t have a fix yet for the brake pad % issue. Or so they claim.
  4. Anyone had this happen with their rear camera system? My review mirror camera still worked fine.
  5. You need a sharp knife, heat gun, rubbing alcohol and a squeegee with a felt pad on it so it doesn’t scratch the vinyl. Look up CKwraps on you tube. He’s pretty good about explaining the process.
  6. Yes slightly. I used VViViD vinyl but I know 3M 1080 is a little thicker but harder to work with but it might hide it better.
  7. Looks sweet! Are they going to wrap the front bumper sensors too?
  8. Didn’t like the plastic looking trim pieces above and below the sliding back glass so I wrapped them in gloss black vinyl this morning.
  9. My 6.2l is the same. 3.5” through the muffler to 2.75” duals that are split over the axle.
  10. Just got back from the window tint shop.
  11. Got the windows tinted today. 5% on the back 3 windows, sunroof and visor with 15% going on the front 2 windows. This was pre-bath today. Sun was at a bad angle, I’ll get better ones this week.
  12. I think you mean a 295 since that’s the width portion of the tire. The 55 is the side wall. I may be wrong but here’s my math... 305/25.4 = 12.00 wide 305 x .55 = 167.55 mm for sidewall. 167.55/25.4 = 6.6” of side wall height 6.6” x 2 + 20” (rim size) = 33.2” overall height
  13. Sub’d. This is the tire size I’d like to run on some 20x10’s -18 wheels.
  14. Not to be an instigator, but what your saying is they don’t want to buy a truck because the tailgate but in reality they’re just lazy by not removing their hitch then complaining that it’s GM’s fault. I don’t pull a trailer enough to justify leaving my hitch in the receiver but I understand the trade off. To get the cool tailgate I’ve got to do my due diligence and remove my hitch. I’m ok with that.
  15. Got my alignment done after my motofab install then got a driving award from the highway patrol on the way to the office. [emoji16]
  16. Here’s my alignment sheet from this morning. Hope it helps.
  17. I went straight to the GM. I knew that I would end up crushing the soul of some sales guy with my negotiating so I skipped all of that. He later assigned me to Justin Mills to do paperwork. I used the spreadsheet posted above to get them to the number I wanted. There was a truck similar to this one at Dunn County GMC by OKC. That’s the only two I could find surrounding me within a reasonable drive.
  18. I did all of the steps listed except loosing the top bolts and removing tie rod. Installation was ok....would’ve been easier talking the top bolts loose. Had it done in about an hour and 15 min without using air tools.
  19. We picked up the new AT4 yesterday and I’ve already debadged it, leveled it and swapped the antenna out. Once my 3M carbon vinyl gets here today I’ll wrap the front GMC logo. I’ll post pics once I get it washed this morning; it rained on us coming home from the dealer.
  20. I get what leasing is, I just don’t understand the why behind it. Similar to renting a house vs buying one.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,759
    Total Members
    8,960
    Most Online
    DM22
    Newest Member
    DM22
    Joined
  • Who's Online   1 Member, 0 Anonymous, 1,560 Guests (See full list)

×
×
  • Create New...