Jump to content


  • Content count

  • Joined

  • Last visited

Community Reputation

0 Neutral

About Sk734

  • Rank

Profile Information

  • Name
  • Drives
    2014 Silverado

Recent Profile Visitors

1,336 profile views
  1. The buttons are hard to use when driving. They are small. 1/4 of a circle. Manual dial easy to reach and set. I like simple.
  2. Is this hard to do? I don't like auto control. If anyone has done this how difficult is it. I have manual controls for my 2014 Silverado LT but it does not plug in to my auto wiring harness. Would the computer have to be reflashed? Thanks for any info. Steve
  3. I have decided to remove the throttle body spacer. The bolts are 6MM X (?) but I don't know what the length is. Can anyone tell me what length is of the original bolts from the factory to mount the throttle body or where to get the info. Torque values? Thanks Steve
  4. I figured it out. They installed a throttle spacer from Airaid also. Since they installed an Airaid cold air intake they did not use the offset that came with the Airaid intake kit to reinstall the GM factory air intake tube.
  5. Here are some pictures and measurements. I am not sure why this part does not fit. Is their an older part #? I would appreciate any insight on this problem. Thanks Steve http://i1135.photobucket.com/albums/m631/mobilcastle/20151223_115024_zpsik7welo6.jpg http://i1135.photobucket.com/albums/m631/mobilcastle/20151223_111546_zpslgtpg1jx.jpg http://i1135.photobucket.com/albums/m631/mobilcastle/20151223_093849_zps6qls8ep2.jpg http://i1135.photobucket.com/albums/m631/mobilcastle/20151223_093827_zpsbn6cberq.jpg
  6. Sounds good-I will go to work on that. Sent from my SAMSUNG-SGH-I337 using Tapatalk
  7. I need some help guys. I really like this truck. I bought a used 2014 LT Silverado 2500 HD 6.0 Flex that was built in Nov of 2013. I am removing an AirAid cold air intake and putting a factory GM unit back in. The rear duct part that attaches to the intake has a baffle that lays on top of the motor.It is way off as far as the rubber bushing that sits on a pin that is on top of the motor-the hole is about 1" short of the pin. The top plastic engine cover sits on similar type pins that are larger. The part they sent me from a GM dealer is a 20872169. Is their a different part (rear duct) that was used prior to 2014? The dealer keeps telling me this is the right part. Would their be some offset that is used with this intake to make it fit? Thanks for any insight you can give me. Oh yea-the reason I am changing the Airaid unit is I am retired and not into noise.
  8. I bought a used 2014 2500HD with 6.0 gas motor and it has a Airaid 200-280 cold air intake. Anyone have a stock unit I can buy or swap? Can use years 2011,2012,2013,2014 with gas 6.0 motor. The Airaid sells for 399 on Amazon. Good deal if you are looking for one-send me a PM. Thanks Steve
  9. I bought a used 2014 2500 with 6.0 motor and it has a Airaid cold air intake. Anyone have stock unit I can buy or swap? The Airaid unit is $399 on Amazon-200-208 should be correct Airaid according to Amazon. I am retired and I like quiet. Thanks
  10. Best # for airaid I can find is 200-280 on Amazon I bought the truck used and that Airaid # is suppose to fit my new truck according to Amazon. (2014 chevy 2500 HD with 6.0 engine) The Airaid unit new is $399 at Amazon.
  11. I bought a used 2014 2500 with 6.0 motor and it has a airaid cold air intake. Anyone have stock unit I can buy or swap? Thanks
  12. Does anyone know who is the largest dealers in Silverado and GMC trucks in the US. I am going to be selling my Silverado D/A 3500 dually and I will be shopping for a new 2500 truck. Thanks in advance. Steve
  13. New truck today!

    Who are the biggest chevy and gmc truck dealers in the US that stock the most 2500's.? I will be looking later this year. Going to sell my 2011 D/A 3500HD dually. Thanks Steve

Important Information

By using this site, you agree to our Terms of Use.