Jump to content

asalinasz39

Member
 View Profile  See their activity

  • Posts

    419

  • Joined

  • Last visited

  • Days Won

    4

 Content Type 

Everything posted by asalinasz39

  1. asalinasz39
    Got this usb led lights to light up the interior. The rear one I left in cuz I can turn it on with the head over controls. The one in the front stays on while running which I didn’t like. Sent from my iPhone using Tapatalk
  2. asalinasz39
    Looks great! So a total of 4” of front lift. How many miles on it with the mod? How are the cv angles looking? Sent from my iPhone using Tapatalk
  3. asalinasz39
    Oh I see! I have that however I want the cargo lights to light up when I press unlock in joint with the bed lights and reverse lights. Sent from my iPhone using Tapatalk
  4. asalinasz39
    I sure hope so! That would be awesome Sent from my iPhone using Tapatalk
  5. asalinasz39
    Jumper wire mod at the BCM? Sent from my iPhone using Tapatalk
  6. asalinasz39
    Oh yes definitely felt like that. I would think people would stare at my truck for the broken mirror rather than a new At4 Sent from my iPhone using Tapatalk
  7. asalinasz39
    Replaced my broken mirror today...feel much better Sent from my iPhone using Tapatalk
  8. asalinasz39
    That looks great! I feel like we need to start a thread of leveling kits and tire sizes for people to share.
  9. asalinasz39

    truck 2

    asalinasz39 commented on atay2011's gallery image in General/Off Topic

    truck 2
    Any rub on those k02s
  10. asalinasz39
    I just want to sync my cargo lights with my reverse lights like I had in my 17. That was more than enough light, but I haven't found the pin #s for the reverse lights from the BCM under the dash plus my diodes haven't arrived. Although someone here said diodes are not necessary.
  11. asalinasz39
    Woow I was just under the impression that mine did; only because the light output is like a brigh white/blueish rather than the license plate which was softwhite(yellowish). But then again I haven't opened up the tailights on my AT4 Edit; just read the build sheet of mine and they are LED backups.
  12. asalinasz39
    Mine are already LED I believe. What trim is your 19? Sent from my iPhone using Tapatalk
  13. asalinasz39
    Replaced the dealership license plate frames with Chrome GMC frames. Sent from my iPhone using Tapatalk
  14. asalinasz39
    I know some running 33.5x12.5 which is a 305 65 r18 that size usually runs in k02, mastercraft, or ridge grapplers. Sent from my iPhone using Tapatalk
  15. asalinasz39
    No codes on the dashboard Will probably get one on the OnStar report as i did on my 17 but no biggy. Sent from my iPhone using Tapatalk
  16. asalinasz39
    Awesome thank you so much for the fine details. Gives me confidence that I can tackle this myself. On my 17 I paid cuz the upper balljoint wouldn’t come loose and I didn’t have a ball joint separator but with your route I can sure handle it. Thanks again bud! Sent from my iPhone using Tapatalk
  17. asalinasz39
    Replaced my license plate bulbs with this JDM ebay bulbs. Took about 5 minutes to do so. I has read it was harder than the K2 and it sure is more reduced in space. Found it easier to remove the socket through the top of the hitch space and then to twist back in i snuck in my other hand through the bottom section between hitch and bumper bracket and with both hands i turned the connector back into place. The light difference output is quite eviden. On the above picture you can see the LED on the left and the incandescent bulb on the right. Sent from my iPhone using Tapatalk
  18. asalinasz39
    Thanks great info brother! My AT4 has a 2.5” rake from factory...I keep measuring and keep getting 38.25 front and 40.75” rear. Sent from my iPhone using Tapatalk
  19. asalinasz39
    @eppieguy So which route did you take to install the lower strut spacer? Loosen upper/lower ball joints...tie rod ends...and sway bar links? Or you tube “easy route” lift truck from front center...remove lower strut bolts and sneak in the spacer in the gap then install new bolts.
  20. asalinasz39
    What are your measurements now: floor to center of fender? Front and rear? Whenever you have a chance if you could share that info that would be awesome. Preferably after alignment and suspension settlement lol [emoji4] Did you install yourself? If yes how did you tackle it? Loosening tire rod end...upper and lower ball joints...and sway bar end links. Or did you follow the “easy way” you tube video where they only lift the truck and loosen the two lower strut bolts...remove and sneak in the spacer then install bolts. Sent from my iPhone using Tapatalk
  21. asalinasz39
    On my 17 I would only see in on the monthly OnStar report. Hope that’s the case with my 19 too. I dont mind seeing it on the e-mail report as long as the DIC doesn’t show a code its all good. Sent from my iPhone using Tapatalk
  22. asalinasz39
    Got my AT4 about 2 weeks ago! Very happy with it. So far only got tints free from the dealer all around Looking into a 1 or 1.5” level. Ordered some LEDS for the license plate already. Sent from my iPhone using Tapatalk
  23. asalinasz39
    https://www.gmupfitter.com/files/media/photo/1085/19_Sierra_1500_Body_Builder_SM_U_2018AUG29.pdf Found the info. So far I was thinking of putting a diode from pin 18 module X2 (gray wire) to pin 4 module X7 (gray/blue wire) and this way have the cargo lamps come on with the bed lamps and have extra light when unlocking vehicle at night or when loading up the truck bed at night. What do you guys think? I would like to include the mirror perimeter lights but I couldn't find them on any of the modules...perhaps I overlooked it. Doc1.pdf Doc2.pdf Doc3.pdf
  24. asalinasz39
    I would at least like for the mirror lights to turn on with the cargo, bed, and reverse lights along with fogs when unlocking...to light up the parking lot lol. Iam sure it’s possible as I had my cargo lights wired up with the reverse lights and they would come on after pressing unlock on remote on my 17. I just need to find the rest of the sheets that the OP attached to figure out whwre to slip in the diodes Sent from my iPhone using Tapatalk
  25. asalinasz39
    I believe I saw a lower strut spacer somewhere at the beginning of the thread! Sent from my iPhone using Tapatalk

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,754
    Total Members
    8,960
    Most Online
    scotthvac.net
    Newest Member
    scotthvac.net
    Joined

  • Who's Online   1 Member, 0 Anonymous, 466 Guests (See full list)

×
×
  • Create New...