Jump to content


  • Content Count

  • Joined

  • Last visited

Community Reputation

31 Good

About Barman84

  • Rank

Profile Information

  • Name
  • Location
  • Gender
  • Drives

Recent Profile Visitors

1,142 profile views
  1. I just put an alpine 455u in my truck you don’t have to run a single wire for this setup... I drilled a 1” hole in the side of the upper glove box cut the stock wires off the back extend the incoming Sid wand the out going side and hooked up the power straight to the stock unit and ground. No rem needed it’s remote sensing and sound hella great. Word of advise... the dash speakers are wired to the door speakers so when you amplify them the chime and everything gets really really stupid loud. It lasted a week before driving me nuts. I ran separate wires from the lines on my dash speakers from the stock unit before going into the map and this solved my problem completely. My 6x9 jLs in the doors still sound great as well. I had some bassy music on the other day when I was taking some of my PVTs to appointments and they asked if I had a sub in my truck which I don’t.
  2. Installed a new rear diff cover while I changed rear diff fluid. Alao i I put on a class 4 trailer hitch from uhaul
  3. Mine lost it at 58k. Got a free one under warranty had a whole 2 months left. They gave me utter hell as I have a lift and 35s that were installed by the dealer... I told them to pound sand and fix it or refund the cost of the lift and tires they did and pay for it with that. Needless to say say I got a new one. However, since that I upgraded my diff ratios to 4.10s from the 3.08s it had my trans temps seem to be way better. The issue is heat with these apparently.
  4. 1500 has 3 lights per tail. 1 brake 1 turn and 1 reverse. I have resistor in everything but the reverse 59w 20ohms
  5. I’m running 2 50w by 20ohm resistors on each side hooked up to the black and green wires top and bottom bulb sockets. Did id they need to be ran in parralel and only to one socket??? I see where the wires run into the bottom and back out. So should they both be tied in here together? This is getting really annoying.
  6. I have aftermarket LED tails. We just got a ton of snow here in Washington state and now I have hyperflash... so i got some resistors as the lights still work just stupid hyper. Attached to green and black did one side only and still hyper flash. Anyone have any ideas? And yes I searched the forum and found nothing.
  7. It’s hard to say on reception when I was stationed in Fort Worth I could pick up hd and regular channels just fine. Now that I’m stationed in Washington state I have trouble even picking up satellite radio. FM is a joke to unless you have zero trees around. I stream almost everything now anywaye. as for my wheels they ride exactly the same as my old setup and look way better. I had the same issue before just not as bad only when making left hand turns. I did switch from an MT tire to a hybrid as well so I’m wondering if that as anything to do with it.
  8. https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F183064142639
  9. I ran my ground wires to the ground in the door. From there I ran the spots to the cargo lamp fuse on the passenger side and the marker light wire goes to the fuse under the driver side for marker lights. I like the cargo switch better. I have extra light to the rear when loading stuff in the dark. Besides the lights don’t put out enough light to actually assist in backing up. I’d actually think they’d be annoying. That and I have an opt7 triple under my tailgate that puts out enough light and then some for backing up .
  10. I have my abs fuse pulled for a good reason. When I swapped from a 20x9 wheel to a 20x12 every stupid round about or turn set off my abs like I was skidding... but I wasn’t it’s not fun to drive when your truck decides to randomly toss the brakes on. The dealer can’t fix it and it irritates me so it’s pulled until someone can give me a good fix. Bearings are all good abs sensors are all good. I have an email to a tuner to see if they can make it less sensitive... And I was playing around with the cluster. The 14s period don’t have the angle approach... so it’s always at 45 degrees. I was going to see what it takes to get it to work since it’s in the cluster.
  11. I like mine. Sorry don’t have an actual full rear pic lol.
  12. It’s the chrome putco handle cover painted to match. It’s an actual pic...
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.