Jump to content

dla

Member
 View Profile  See their activity

  • Posts

    109

  • Joined

  • Last visited

  • Days Won

    3

 Content Type 

Everything posted by dla

  1. dla
    I have some Belltech rings you can have, just let me know where to send them.
  2. dla
    Belltech 6521-003
  3. dla
    For what it's worth... my Belltech 6404-100 shackles that came with my 7" flip measure 3" eye to eye.
  4. dla
    Not sure on your 4X but my Belltech spindles worked with my stock 17's. they supply a thinner nut for the lower ball joint stud that needs to be trimmed.
  5. dla
    I added them... GM 84154470
  6. dla
    I think I've only bottomed out the rear 1 or 2 times in 40,000 miles... my tires kiss the liners before I hit the stops.
  7. dla
    Flip your drop ball mount...
  8. dla
    I'm right at 5" in the front with no rings on the left and an 8mm ring on the right to compensate for the lean.
  9. dla
    Yea, those photos were from when I first lowered it while on the stock 17's. I'll measure from wheel center and get back to you. Yea, those photos were from when I first lowered it while on the stock 17's. I'll measure from wheel center and get back to you.
  10. dla
    Just for comparison... my Belltech 7" flip, stock hanger w/shorter shackle (as pictured above) gave me about 7 3/8" drop.
  11. dla
    If you are staying with the 2/4 drop you could easily go to a 305/50R20 and get about 1 1/2" more width while staying at the same 32" overall diameter. I'm running 275/40R22 (30.6") up front and 305/40R22 (31.6") out back on a 5/7 drop...
  12. dla
    Factory Reproductions 22"X9" (+31) with Nitto 420S 275/40R22 (front) and 305/40R22 (rear).
  13. dla
    Finally pulled the trigger on some new wheels and tires yesterday... 275/40 and 305/40 Nitto 420s on 22" chrome replicas.
  14. dla
    No, I did not... is this necessary?
  15. dla
    Installed an Airaid MIT and AEM Dryflow filter...
  16. dla
    Might as well add mine to this thread...
  17. dla
    My mistake, just did a quick search and went off the title.
  18. dla
    There's a few on ebay... http://www.ebay.com/itm/BRAND-NEW-OEM-Jet-Black-Center-Console-For-2015-up-Sierra-Yukon-Tahoe-Silverado-/401026711938?hash=item5d5f0e0182:g:QukAAOSwvt1WRojS&vxp=mtr
  19. dla
  20. dla
    Total wheel width on a 8.5" rim is 9.5" (241 mm). The 8.5" is the width of the seating surface for the tire bead not the actual total outside width. A bit confusing but backspacing is measured from the outside edge of the backside of the wheel. Offset is +/- from wheel center.
  21. dla
    It's actually just under 5" in the front... every now and then on a high speed type shallow dip (freeway) it will rub the inner fender liner. I think the Belltech struts are somewhat stiffer than the stock ones so that is helping minimize the rubbing. I did not get any rubbing when I was at 4". I'm still running the stock 17's (31" tall) and will be going with a staggered fitment once I decide on a wheel. Probably going to end up with about a 29"-30" tire up front with 31" or so in the rear.
  22. dla
    Bell Tech Street Performance front and rear... pretty happy with the ride.
  23. dla
    The fit is really nice and it looks like it should be pretty much water tight.
  24. dla
    Installed an Access Vanish roll-up tonneau cover.
  25. dla
    Hope this helps... Mine measures 32" from the dash to the rear top edge of the console. The back of the console curves further back some as it goes towards the floor. The space behind the console to the back of the cab (carpet panel) is about 7" at the top and 5" half way down to the floor.
×
×
  • Create New...