Jump to content

rogah

Member
 View Profile  See their activity

  • Posts

    220

  • Joined

  • Last visited

 Content Type 

Everything posted by rogah

  1. rogah
    Sent from my iPhone using Tapatalk
  2. rogah
    any paint chipping/scratching on the sides from stuff kicking up? any paint chipping/scratching on the sides from stuff kicking up?
  3. rogah
    any paint chipping/scratching on the sides from stuff kicking up?
  4. rogah
    well thats embarassing haha such a weird spot. surprised i never noticed it
  5. rogah
    hmm.. i will check when i get back into my truck. i never noticed something below the 12v.
  6. rogah
    I drive a 2014 Sierra SLE that does not have a 110v next to the ash tray, only a 12v. For the upper trim panel kit, do I only order the panel kit WITHOUT 110v? Or is it possible to buy the one WITH 110v and route some power to it?
  7. rogah
    Sent from my iPhone using Tapatalk
  8. rogah
    RC2.5" front level only 285/45/22 Pirelli tires on 22" GM rims Sent from my iPhone using Tapatalk Uneven ground in the first picture, the front is NOT higher than the rear Sent from my iPhone using Tapatalk
  9. rogah
    but why turn em off when they look so good lol jk. i will test it out and see how i like it
  10. rogah
    going to change from 10-18 to 10-22 pin tonight, rather keep the fogs on all the time
  11. rogah
    Anyone know the biggest tires that can be put on 22" GM rims with a RC 2.5" level while having no rub and no offset?
  12. rogah
    what size tires and rims are those?
  13. rogah
    I'm looking into leveling my truck but am new to the whole leveling thing. Will the 2" front lift balance the truck out? Or will the 2.5" RC level kit be better? And why do people put bigger rear blocks in? My 2WD Sierra SLE has 22" GM rims with 285/45/22 Pirelli tires. I just measured the rear and front height. 36" front and 39.5" rear. Even with a level kit I won't be level?
  14. rogah
    where did you get the denali grille?
  15. rogah

    Rear angle

    rogah commented on Kander41's gallery image in General/Off Topic

    Rear angle
    what bed cover is this?
  16. rogah
    I originally took out the ONLY the muffler and replaced it with a super 44. when they started it up, i was not surprised at all, i barely heard an increase in loudness but did hear a much deeper sound. I was like **** i will drive a day to see how it is. the next day i went back and had them take out the resonator and clamp the valve open, never been more happy since
  17. rogah
    i see i did the same thing as you haha thats nice to hear! i am about to install an airaid jr kit, it just came in
  18. rogah
    nvm i think this will work: http://www.gm-trucks.com/forums/topic/167609-airraid-mit-installed-on-v6/?hl=intake+coupler
  19. rogah
    actually before the tune i want to add the airaid jr kit. i see that you made your own pvc pipe. is there a way to convert the airaid kit to 4.3l v6 version?
  20. rogah
    whats your opinion on the Diablo Sport intune? and does adding this void warranty?
  21. rogah
    drove from the muffler shop back to my house ~10 minutes on city roads, no highway. BUT I LOVE THE SOUND NOW! removing the resonator and opening the valve sure did cause a significant increase in deep, grumbly sound. Can't say anything about the v4 noise cause I haven't driven on the highway yet for it to be noticeable. but omg it sounds delicious, like a v8 ~~ might go get a tune doe. after chopping off the muffler, resonator, and opening the valve, the shifting is a bit off? higher revs before shifts
  22. rogah
    Flap is now clamped open and I had the resonator chopped off just now. I'll write up a review soon
  23. rogah
    why would it be worse do you know? i was assuming v8 are naturally louder which would therefore have a higher chance of louder drone/??
  24. rogah
    because i drive a v6, do you think i won't have a drone?
  25. rogah
    i have a 4.3l v6 so its still quiet with the 44. i might cut the resonator and clamp open the valve. if i get really bad drone then ill unclamp the valve. what do you think? I dont plan on moving the valve to before the muffler
×
×
  • Create New...