Deanjo

Can't say I've ever heard that whistle. Here is mine with the windows up.

Yup they will, same box on the 2014-2016. They do just stick on with 3m tape. I used 3m adhesion promoter as they recommend as well since I had some laying around. Just be sure to line it up put it on right the first time. That 3M tape with the adhesion promoter sticks hard and you do not get a second chance.

Oh probably if you book it in as a service. I just didn't want to book yet another appointment with the dealer for something that cost $30 and takes 10 minutes to put on. My time is more valuable to me than to wait around for hours to have something like this done.

They do not go on the door, they go on the truck box corner and you get them from GM.

There is a GM service bulletin on it BTW #PIT5454 - Paint Chipping on Front Lower Bed Corners Subject: Paint Chipping on Front Lower Bed Corners Models: 2014 Chevrolet Silverado 1500 2015 Chevrolet Silverado 2014 GMC Sierra 1500 2015 GMC Sierra The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern Some customers may comment about excessive paint chipping on the front lower bed corners of their trucks, as shown below. Many of these trucks spend a majority of their time on dirt roads or gravel roads Recommendation/Instructions To better protect this area, a bed corner shield has been developed to protect this area. The shield is held on with double back tape. The part numbers are 23469126 23469127

Ya, they started putting them on the 2016's after multiple complaints. My dealer wound up fixing the chips and then I put them on to keep them in good shape going forward.

Simple add on but needed on these trucks. Added the corner guards to the box corners right behind the cab. Should have been something that was standard.

Nope, you are not the only one. I personally do not like the levelled look as the top of the truck box is lower than the hood on this body style. Put a bit of weight in the back and it looks like a dog dragging it's *** on the ground. If I were to do anything it would be a lift and level with a 2.25" in front and a 3" in back.

I've looked at many of those, all are too big to fit in the tray. The idea is to use the tray, not to replace it. The closest solution that would fit that I can find is from China and the shipping cost makes it prohibitive. http://www.aliexpress.com/item/Tool-case-toolbox-suitcase-Impact-resistant-sealed-waterproof-ABS-case-260-200-143mm-camera-case-Equipment/32608612314.html?spm=2114.13010308.0.50.Y2Yh6E

I liked that idea but I've been having one heck of a time finding one that would actually fit in the tray. Even small plastic tool boxes that would fit (and are reasonably close to battery size) are hard to find. If someone ever made a toolbox using a battery casing, they probably would make a killing as a GM accessory.

OK thanks, I was wondering someone came out with a premade box that allowed it all the way back. Guess I'll keep my custom one and redo it to match the interior.

Are you still able to move your seat all the way back with those subs in place?

Ya, I was pretty pleased, even found a place for my DQ-61's controller (that's what the knob and LED's are under the 12-volt outlets are). My biggest concern was to have to redesign a sub-box if it was too long but that turned out just perfect as it allows just enough space for full sub cone excursion. May still redo the box as this one was supposed to be just a temp one and do a bit of conturing of the box edges, then get it wrapped in matching vinyl to give it a factory look. May even move the sound processor into the large bin with a false floor over top of it to protect it since it is so huge. I may just wait on that mod as AudioControl's new DM-608 processor should be out soon.

Squeezed it in.

Pretty sure you will not need the rear trim plate.

Me too!!!!

Well ordered my parts for my swap today. Damn that exchange rate hurts but it is going to cost me in the neighbourhood of $900 to complete. As far as the front USB goes, I'm actually planning on not using those at all and instead use the location to mount my AudioControl DQ-61 remote. Getting the side panel trim has been a real chore however, everywhere I tried to order online was either, would not shop to Canada, had one but not the other, or said they would have to back order it for me because apparently GM is out of stock. Wound up ordering those pieces through the dealer in the end. You guys with the regular cab conversions, did you take out the middle belt or just let it hang? If you took it out, how much of a pain was it to remove that back plastic on the cab wall to remove it. Also does it hang any further back towards the rear wall than the jumpseat did?

Dammit, I bet the 2017 Sierra will get a sock drawer too.

It is tight but it can be done.

Judging from this eBay listing I would have to say that mine is reverse tartan. http://www.ebay.com/itm/Factory-New-GM-Front-Center-Console-Trim-Panel-Tray-Reverse-Tartan-22995091-/141685915473 According to the local dealership the new part numbers for my set is: 23466980 CONSOLE ASSEMBLY, W/O DENALI, W/O REAR DVD, BLACK (anybody know the difference between denali and w/o denali?) 22817347 Console Panel. Side trim. 23467516 Console Panel. Side trim 23467112 Plate UPPER TRIM, W/110 VOLT OUTLET, REVERSE TARTAN 22776807 Console assy front bracket. Console Bracket

This is what it looks like from a bit of a distance.

Ya it is "silver". Hard to tell if it the same with your picture as it is hard to see the texture detail.

Question.... is this trim style what they call reverse tartan? If it is please correct me if I'm wrong but for my 2014 silverado I would need the following parts to replace the jump seat with a console. 22995069 22817347 23467516 23467112 22776807

Just the factory Z-71 grill with Cloud-Rider stainless steel spectare mesh inserts. Just bolt right in.