wuznme

Have CK156 Reps, I'm surprised they were lighter, the first set of wheels had specifically looked for some light wheels and these were even lighter.

Nick Williams isn't making them yet, Katech ported Tony Mamo ported WeaponX ported Katech 103MM, but way too much for a stock motor Any of these places are porting the stock TB to have them flow better, some report a few HP gained, wouldn't buy it for that, not sure I really believe it, does improve the throttle response a great deal.

Very nice indeed, when it comes time for the 103MM I'm gonna send him the whole blower to port as well the heads will be sent to him too.

I got the Tony Mamo ported TB, the Katech 103 was looking at needed too much work to fit and until I build a forged 416 and turn the boost up, really don't need it.

Keep in mind these are 3" and it doesn't flow any better than the stock exhaust you have now.

100ea ??? My 22's weigh less then the stock 20's only by 2lbs..

From my NBS heated seat swap experience, not worth the headache better off buying a aftermarket kit.

It's not an old Vette motor, this is current platform Vette TB. Although I would suggest a ported TB from one of the Vette forum vendors. throttle response is so much better

My truck is CC and used the same shocks as I gave you part numbers for. I thought they were perfect for the drop and truck. You were lower than me, so maybe something happened to them. I'm still using mine after removing flip kit and dropping the rear with shackles and block removed. Although it's getting ready to get dropped again.

Yes, For stock. I have Bilsteins so the corners needed none.

Basically

I put the truck back to stock height with a level in the rear for an exhaust, now I pulled the exhaust off and going put the flip kit back on change mounting position in front again.

Yep, my girls 2013 Runner has been flawless after 60k miles. My 2016 Sierra has numerous problems, some that can't be resolved yet...

PM sent... You wont have to change the sleeves and bushings, will come with bushings installed and 2 different size sleeves that slip right in.

I think you'll be good with the 2inch shorter Bils, the Belltechs are spec'd up to 7in drop and they are 20.5 which is what the Bils you have now are. Or Ridetech's but they $135 or $185 a pop...

It would be nice if GM stopped the heated seats from being controlled by the BCM, but I still think they do. Tried to do this on my old NBS truck, was PITA and never worked. I had the following to work with when trying: Heated seats Harness from vehicle Door panel switches BCM from vehicle The schematic was pretty cut and dry for this and was a no go. The power piece for a seat swap should be cake.

I know at one time (probably when eff'n around with the crappy DJM flip kit) that they where the same length, depending which way your pinion is pointed will determine the amount for one side being longer/shorter than the other. Nose down will always make the passenger side longer Nose up will make the driver side even/longer depending how much it is pointed up. The shock isn't shorter, what is stated above will determine the shock mount being shorter/longer.

Check out Ridetech shocks, they are made by Fox...They will have shorter ones and they're good shocks, ran them on my bagged truck

McG spindles have been that way forever, the 17+ spindles will always need the ball joint trimmed. Lol... 17" wheel is a 17" wheel whether spare or not. You could always swap the wheels on the side of the flat and put the spare on the rear. You mean too long going from 6-7, spec out shorter bilsteins. This part #33-062518 can use the same bushing/sleeves from current ones and 2in shorter. Out of the box they're same size, not labeled L or R. When installing the rear shock passenger side appears to be longer if the truck is in the air; if the truck is on the ground they're same length eye-to-eye.

Warranty them out, or did you use them past the specs of them....lol

Or Jones Exhaust since that is who owns them now.

Man those things aren't doing any good sitting there...Send them this way!

You're going to want some Ride Tech RQ or HQ shocks go to the web site with your measurements, they will have something.

Little over 1/2 and nets about 7/8 of drop. truck doesn't ride very good like this though..