Jump to content

Kennedy81

Member
 View Profile  See their activity

  • Posts

    99

  • Joined

  • Last visited

 Content Type 

Everything posted by Kennedy81

  1. Kennedy81
    It can be made to work on the 5.3 http://www.performancetrucks.net/forums/gmt-k2xx-trucks-general-discussion-221/c7-intake-manifold-my-5-3-a-531361/
  2. Kennedy81
    Did you buy the invis-a-rack with the tonneau, or seperately? I want to get one, but didn't have the money at the time to buy the combo, so I just bought the Low-Pro tonneua. Wasn't clear if the rack could be added later or not.
  3. Kennedy81
    Where did you pick up the power from?
  4. Kennedy81
    Not that I noticed. If metal is going to warp during powder coating, it would be during the prep phase when the media blast it. If whomever does it just uses sand/silica, it can cause more friction and heat the piece up and cause it to warp. When blasting stuff like this, they really need to use a "soft" media, like walnut shells or plastic pellets.
  5. Kennedy81
    picked mine up from getting re-painted. I bought it off the lot with some cosmetic damage due to a tornado. I also had the bumpers powder coated black. I'm planning on getting the grill and headlight surrounds done in black also. I'll post more pics when it is all done.
  6. Kennedy81
    Cargo/Accessories installed the time of measurement, amount of fuel in the tank, possible a slight slope where they parked, how/where they meassured, how long they've let it settle after install, etc, could be all kinds of things, shoot, I've even seen some tape meassures that are a little different from one another. Variances by 1/2" wouldn't surprise me at all.
  7. Kennedy81
    This may help... http://www.gm-trucks.com/forums/topic/160916-silverado-police-truck-ssv-part-numbers/
  8. Kennedy81
    http://www.gm-trucks.com/forums/forum/168-gen-v-small-block-engine-drivetrain-exhaust/
  9. Kennedy81
    Where did you get that tip?
  10. Kennedy81
    I wonder if one of the under seat organizers could be trimmed to still work with the sub?
  11. Kennedy81
    Thank you
  12. Kennedy81
    Anyone have any pictures of the nFabs off the truck, and then how they mount? I may just build my own...
  13. Kennedy81
    This mod would be nice to check out hotties in a car behind you at a light... lol
  14. Kennedy81
    Did you plasti-dip the "SILVERADO" as well? If so, did you mask the letters off on the truck, or remove them and re-apply them?
  15. Kennedy81
    Its finally been above freezing here the past couple of days, around 40+ degrees and according the DIC, with the warmer temps, it appears I'm getting about 2-3mpg better than when it was below freezing out, around 20 degrees. I have yet to run a full tank since it has warmed up, but based off the 25 mile average, I'm definitely up.
  16. Kennedy81
    So a 30HP gain with just exhaust? Is that based off of adverstisted HP numbers, or what it dynoed prior to the exhaust also? Curious if it adds in few milage as well.
  17. Kennedy81
    http://www.gm-trucks.com/forums/topic/158148-remove-oem-badges/
  18. Kennedy81
    Thanks for sharing. Did that $1000 include the cost of the winch, or in addition to? Just curious. Thanks
  19. Kennedy81
    Mine did something similiar, only instead of black out, the screen "scrambled". I took it to the dealer, they tried to get it ti repeat that problem and had no luck. They did end up finding a software update for the Mylink system, so they loaded that, it hasn't done it since, so i'd guess the update fixed the issue.
×
×
  • Create New...