mkeddie161

Bed heater installed should work as good as the last one Sent from my Moto Z (2) using Tapatalk

If u figure it out let us know would think if u have front collision alert it should be somewhat doable but not sure what programming u could use since it's not event a option on the fully loaded trucks Sent from my Moto Z (2) using Tapatalk

Alot no but where I got mine they have 2 or 3 on the lot western ny Sent from my Moto Z (2) using Tapatalk

I put in timbrens so it doesn't beat up the suspension...will swap back to standard bump stops after winter Sent from my Moto Z (2) using Tapatalk

https://www.ebay.com/itm/184245343401 This is a easy fix Used this for my tailgate bar But that picture isn't of a 2020 hd.... Sent from my Moto Z (2) using Tapatalk

I think it is the single cab long box that does the most ....but don't quote me on that Edit nope I was wrong kind of misunderstood the overall question So I think the only way to figure out ur available payload is by scaling I don't think the door sticker takes into account the add ons but haven't looked at that But the lower the trim the higher available payload due to less stuff in the truck Sent from my Moto Z (2) using Tapatalk

That all sounds good to me....I want that setup now tho...mine will basically be the same way tho it has a voltage sense switch to turn relay on and off .... Now u just have to put one of these in so u know where ur battery level is Sent from my Moto Z (2) using Tapatalk

So the 100 amp that is in that box I would assume goes to the other battery.. Sent from my Moto Z (2) using Tapatalk

So that definitely looks like a isolator it looks like the 100amp fuse would be ur power coming in(charge wire) and the only thing powered by the battery is the 30 amp fuse... Warning always think that a disconnected wire is gonna blow up in ur face... I'm not responsible The way to see what is happening is to disconnect the 100 amp fuse and take a tester and see what power is coming to the cable that was hooked to the fuse if it's powered then that should be ur charge wire. If the isolator side of the 100amp fuse is dead(0volts) then ur second battery will only charge when truck runs and discharging should not kill start battery With out some testing it's hard to say how it is working just need more info wish I knew they made that before I started my project Wish I knew about that isolator sooner My bought fuse block is from a diesel pickup...it has a 400 and a 175 amp fuse in it Sent from my Moto Z (2) using Tapatalk

Not sure about that model but mine is on the end of the turn signal switch.....where the old cruise set button was Sent from my Moto Z (2) using Tapatalk

Like I said post up some pictures or can't help out much....if it's from the factory I dont think it's a isolator.... Sent from my Moto Z (2) using Tapatalk

Without any pictures I can't say if u have a isolator but from the stock Diesel( not saying u have a diesel) that I've seen there is nothing to separate the batteries they just work together all the time Kill one kill both Sent from my Moto Z (2) using Tapatalk

So finally got my second battery installed and charging It's just a quick install to try out this smart relay will finish cleaning up after I know it will work for me Sent from my Moto Z (2) using Tapatalk

Currently adding second battery as we speak Sent from my Moto Z (2) using Tapatalk

Pictures of isolator and under hood area Sent from my Moto Z (2) using Tapatalk

Do u have side detection If so the sensor is in the bumper step it may be blocked (mud or debris) or maybe broken wire or something like that I would assume the dealer would have already found these issues Sent from my Moto Z (2) using Tapatalk

Should be able to to order the seat back Check out "my upfitting" and u can see how to remove it U will probably have to go to a part dept at a dealer and have them figure out the seat u want ...color/storage Sent from my Moto Z (2) using Tapatalk

https://r.tapatalk.com/shareLink/topic?url=https://www.gm-trucks.com/forums/topic/238565-my-upfitting/&share_tid=238565&share_fid=33003&share_type=t&link_source=app I don't think so Post 35 has my 35s They barely caught when full lock.... But let me know if they do so I can go bigger Sent from my Moto Z (2) using Tapatalk

These trucks have been out but u do have to add in that r+d was slowed down and parts/peices are getting hard to find thanks to covid.... Bought a polaris general a month ago and I couldn't get any accessories for it due to backorder Some aftermarket part makers are waiting to get there hands on the vehicle to be able to mock stuff up Sent from my Moto Z (2) using Tapatalk

So im in the process of ordering my truck and trying to get all the info on everything that im gonna need to get it built when I receive it few questions 1 what is the amp rating on each switch. it says there are 3 30 amp and 2 20 amp I don't think I will exceed any of those but want to know before I layout what they will activate. 2 is the roof beacon wire already predetermined in the switch layout. I plan to run a 'roofbeacon' but also some other cornering lights. 3 some of the bulletins posted here are for the 1500 are they the same for the 2500 any help would be great pictures/videos would be better to help everyone thru this thanks mike