Jump to content

saber

Member
 View Profile  See their activity

  • Posts

    38

  • Joined

  • Last visited

 Content Type 

Everything posted by saber

  1. saber
    I have a brand-new Gibson Part Number: GIB-BM0101 muffler and deluxe band clamps. It was for and fit my 19 custom 5.3 Trail Boss Free, you pay shipping (throw in a few bucks for my effort if you like) 4.75 out of 5 stars ( 11 )
  2. saber
    3D printed
  3. saber
    files sent
  4. saber
    Replaced with 1" blocks
  5. saber
    I can see if you put the tapered blocks in backwards it would cause excessive stress on the u-joints
  6. saber
    The blocks are tapered, if you put them in correctly the driveshaft alignment is fine.
  7. saber
    Sent
  8. saber
    I changed out my console lid to one with storage but there is no organizer available for the jump seat type console so I made one on my printer. I have the .stl files for these if anyone has access to a 3Dprinter.
  9. saber
    Yep, there were plenty of threads and they were not stretched,
  10. saber
    110lb/ft then 100 miles later 120lb/ft. Just a gut feel on that!
  11. saber
    Finally got it the way I want it so I can post a pic. K&N, console lid w/storage swap, llj interface w/under front seat sub, bed mat, slim crossover poly tool box, rear mud flaps, removed 2" spring blocks & installed 1" for leveling, wheel liners, flap open and screens covered
  12. saber
    https://www.ebay.com/itm/Rear-Lift-Kit-1-STEEL-Blocks-w-U-Bolts-1999-2019-Silverado-Sierra-6Lug-4x4-4x2/251983841184?_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D1%26asc%3D20131003132420%26meid%3D0d0d45a1956c44e2a9aab9a702788803%26pid%3D100005%26rk%3D2%26rkt%3D12%26mehot%3Dag%26sd%3D252445736848%26itm%3D251983841184%26pg%3D2047675&_trksid=p2047675.c100005.m1851 This came with the u bolts which i did not use. They were fine thread which I did not like. Used the stock ones as with the lower blocks I was on new threads and they were not stretched.
  13. saber
    Did this and no you cannot reuse the clips.
  14. saber
    I took out the 2" and installed 1" Looks right now
  15. saber
    I took out the 2" blocks and replaced them with 1" blocks. The back now sits about 3/4" higher than the front, looks perfect!
  16. saber
    These are some of the highest selling vehicles on the planet, I can't believe there isn't a good hi-po replacement muffler for them other than a $350 muffler!!!!
  17. saber
    Anybody know which of these wires are the + and - of the front speaker wires. Are the left speakers wires in the same place on the drivers side?
  18. saber
    $276 at GMpartsoutlet
  19. saber
    Nope!!!
  20. saber
    20 gauge AL sheet from Home Depot, tin snips, SS tie wraps- 15min job
  21. saber
    Perfect - thanks
  22. saber
    Thanks - good to know. What do you torque the new ones to?
  23. saber
    Covered the all six now slightly louder than stock - no drone yet.
  24. saber
    Just covered the back 2 (figured the lowest frequency) very little difference.
  25. saber
    Anyone??? I'm changing my rear spring blocks and not sure of the u-bolt torque.
×
×
  • Create New...