Todd1982

Am I doing this right ? Asking for a friend

Let's resurrect this old thread ... Installed the 7735 rear sway bar on my 2014 2wd Silverado on 4/6 drop . Sway bar installed fine and works great . I can not get the spare tire back in place , there is no room for it now . Anyone else with a lowered truck have this issue ?

Good morning Would anyone know the stock size U joint for a 2014 Silverado 1500 2wd ? Thanks in advance

What mods have you done to your truck so far?

Sell the front separate ?

Just saw this ... I finished all this back in April of last year... I thought i posted in here the functionality of each wire . The information being sent to the Dash is over the MOST Bus the alpine does support MOST Bus If you recall during the install you removed that plug and never plugged it back in. Let me know if you have any more questions

https://corrosionfree.com/?_vsrefdom=adwords&gclid=EAIaIQobChMI3prxn8mW5AIVAZ-fCh2NQgG0EAAYASAAEgIz7vD_BwE That is the product that was applied to my truck

Just found this topic... Bought a 2014 truck with 39k on it from new mexico in March ..... Has never seen snow or salt , frame looked flawless. Brought the truck back to Michigan (home of salt and shit roads) had it professionally fluid filmed immediately when I arrived in Michigan. I have noticed the fluid film has attacked the factory undercoating and it will actually wipe off with my finger , leaving bare metal under it . I hope to not drive the truck in the winter , but I am concerned about rusting while the truck sits outside in my driveway during the winter months .

following

My kit came with the clips for the wires . I am mostly concerned with how to attach the lights to the bed . Drill holes ?

Any pictures of the clips you used or what you did ? Thanks

Just got a set of the OEM lights 20979073 for my 2014 Silverado. My truck came with a set from the factory , but I wanted to add the extra 2 like everyone else has done . I don't see the place to mount the extra 2 in the bed . There are no spots to screw them in , unless I make spots Any ideas ?

Anyone have the torque specs for the following items after header install . Steering shaft bolt Transmission Cross member bolts Transmission mount nut Thanks

The whole point of a big brake kit is to stop better and fill the wheel up. If you still running the stock size rotor then what is the point ?

Hello Currently have a 2014 WT with chrome solid front bumper , what do i need to upgrade to the fog light bumper ? I have just the front bumper with no brackets located ready for purchase , will all my brackets swap over ? Will I require any other parts (besides the fog light themselves) to complete this upgrade ? Going to use this harness https://www.gen5diy.com/collections/gen5diy-truck-products/products/14-18-silverado-foglight-harness Thanks in advance

I purchased all 4 handles from a yard for 330 shipped How do I disassemble the front chrome from the LED to paint the whole handle ? I dont want any chrome, also i dont need the metal back plate that came on the drivers door handle ? Thanks again

Anyone running Kooks headers that has added wideband sensors ? I am wondering how much room is available for the wide band sensors pre cat . Is the y pipe real tight to the body under the truck ? Thanks

Great information in this thread Have a couple of questions .... I am starting with a 2014 WT with i04 package I have added the rear camera , but have not paid to have it enabled yet . I purchased the heated wheel with the proper (heated) clock spring. I want to install the Denali dash later this year as well. I have ordered the Alpine i209-GM for a radio replacement . First question .... Should I bother paying to have the HMI flashed for the backup camera since I will be using the Maestro going forward ? Second question .... Steering wheel controls, should I bother to run them to the stock radio at this point or just wait to run them directly to the Maestro ? Third question ..... Will the Alpine unit display radio information to the DIC display ? If it will not , then there is no point running those wires either ? Thanks in advance