Jump to content

Can Some One Find Me An Invoice?

kbzx6r

Recommended Posts

kbzx6r New Member

kbzx6r

Posted
Posted

This is my first post, I have been a long time browser though. My question is can some one find me the invoice price for a 2008 Tahoe? The VIN# is 1GNFC13068R182756. Thanks to anyone that can help me out. I want to go the dealer very prepared.

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

Give me a minute....

 

OK,List is $47,735.00...Dealer invoice is $43,782.08

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

Well personally I think its a good deal,But I think a lot of the guys will disagree with me.

It won't hurt to ask for lower than invoice,The worst they can say is "no".

Live2FlyLow Enthusiast

Live2FlyLow

Posted
Posted

From my recent dealings with GMC salesmen (about eleven in four states), they haven't been willing to go below invoice unless you are considering another vehicle on a different lot (ie. dealer trade) and they have a vehicle on their lot that has too many of the features you don't want. For example, the salesman was willing to deduct the price of the rear entertainment system from invoice and offered that price.

 

If you seek a price below invoice and get the "We have to make a profit" or "My family has to eat" type of reply, you could mention the 3% based on MSRP holdback money that is in the mix -- but don't expect to negotiate on any of that money.

dannynoonan Enthusiast

dannynoonan

Posted
Posted

Invoice is fine. I just bought my 08 Sierra two weeks ago for 1000 under invoice and no doc fees. Did have to pay TTL. I had good success end of the month. I did everything over the phone and through e-mail. I talked to ten and had three aggressively pusue me. They would give me the best price. Everytime they would call I would tell them someone beat them. They would then drop 300 under the other guy. I ran out of time at 1000 under invoice. It was a pain, but it was the most money I ever made per hour.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined

  • Who's Online   0 Members, 0 Anonymous, 284 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • newdude
      2 speed transfer case optional now?

      By newdude · Posted

      This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Coastie05
      give me some tips to make my truck look better

      By Coastie05 · Posted

      Go back to OEM wheels. 
    • newdude
      2020 Trailboss 6.2 replacement

      By newdude · Posted

      Probably not their first rodeo, so it should go as planned most likely.  Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together.  We usually put 50-100mi before we hand them back so if something happens, its not after you get it.  A coolant leaks, oil leaks, a ground left off or loose, vibration, etc.     The new engines so far have been good?  There's been a couple that have popped out there again (the replacement engine) but most have been okay.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...