Leaderboard

Took a trip to the wild Wild West [emoji38]

Pop & Lock Power Tailgate Lock Part #: PL8140 http://www.popandlock.net/Power_Tailgate_Lock/Power_GM_Tailgate_Lock/Power_Sierra?product_id=141 1) Unlock & lower tailgate. 2) Remove (8) torx/star screws from inner tailgate access panel. 3) Remove panel and you'll see lock assembly [pic 002] 4) Remove old retailer clip & cam arm [pic 003] 5) Replace with new cam arm & retailer clip [pic 003] 6) Remove bolt on lock side, and place power assembly inside, lining up existing holes [pic 004] 7) Make sure metal slide in between white plastic prongs, next to cam arm, then replace & tighten bolt [pic 005]

Picked up a protecta bed mat today at agri supply. Had been considering it even tho I have linex....but wasn't sure. Had been looking at dee zee....was in agri supply for something unrelated and saw them. A quick Google search says they are the same as dee zee. Brought it home.$74.99 and instant gratification. Sent from my Note 4

If I am not mistaken the majority of the silverado/sierras have a hollow aluminum drive shaft anyway.

LMAO ! We have a keyboard warrior here my friends!!!! I guess your momma dropped you on your head. These are Factory Accessory wheels powdercoated and not dipped and my turd looks better than yours little boy! RT

I am thinking dump O2 sensors and add some headers. No inspections here Ryan

I agree not perfect, but for a soft budget cover it really stays dry with this system. Also i tried this morning, and realized you dont even have to roll it back. Just open tailgate, disengage latch, close tail gate, the push down to relatch. Its pretty fluid that way.I like the bedrug idea, although i do have a spray-in. Does the bedrug have adhesive to hild it in place? If so, im not sure how well it would work with that...

Can't fix stupid. Looks like he's just burning his bridge on the way out, with him selling his truck. Sent from Tapatalk App - Samsung S6

Nice man. Ima have to look into the bedrug for sure. As far as the tonno seal goes, yes it should be adjusted where the flap should sit atop the tailgate. I also was fighting the seal every time i opened and closed the tailgate until i had a "duh" moment. Next time u open the tailgate, release the latch on the cover and roll it back, one roll. Then close tailgate and roll the tonno closed till it snaps after closing tailgate. It will the sit on top of the tailgate easily.

Ditched the 305/55 idea and went with 305/50. That's a one inch difference and it makes a big difference. I'm going to finish it up tomorrow, but here's what she's looking like right now. 20x12's on 305/50r20 Toyo AT2's 2.5" Level. & a comparison of the new setup vs stock with 2" spacers

Do you have a link to those led running board lights?

LED running board lights I found on ebay. They work awesome.

Awesome buddy! Glad u got the tonno!How much was ghe bedrug? And where did u get it?

I got my new Tonnopro Lo Roll tonneau cover installed. I'll post some pics when I get some better light. Also have a bedrug coming tomorrow. Cannot wait to get that in my bed. So looking forward to camping out of the back of my truck. Sent from my iPhone using Tapatalk

This is a 3-5 also

Out at work

Even light output with sharp cutoff using stock projectors and adjustable offset LEDs!!

2015 Colorado & 2015 Silverado Both in Silver Ice Metallic!

Got her all cleaned up today in preparation for tomorrows road trip to DFW. Gosh I do enjoy going home. Sent by a simpleton struggling to operate an iPhone.

Loving my new toy.

Finally got the methods wrapped in duratracs and put on the truck.

So, with the 10-22 jumper, can you shut the foglights off if you want?

Hey Danger, Which TRS kit did you go with? The 35 watt or 50? Also which bulbs? Thanks

My method is pretty DIY! I take a wire coat hanger and cut free the bottom straight piece. After cutting, the tips are sharp. On one end, I tape up about 3" of end of wire parallel to wire hanger. Then push the other sharp end through the grommet. It makes a tiny hole then, as you pull the wire through, it stretches the hole just enough so it'll pass through. Makes a really tight seal, so no silicone needed. That was a typo... I used a PowerProbe http://www.powerprobe.com/