Jump to content

99 K1500 Silverado 5.7, Need new Cats

dietz4ibanez

By dietz4ibanez
in New Member Introductions

Recommended Posts

dietz4ibanez Senior Enthusiast

dietz4ibanez

Posted
Posted

Well I have almost 200,000 miles on my truck and periodically my engine light comes on for catalyst efficiency bank 2. Well I have debated going to auto zone and spending the $70 bucks or whatever cutting out the old cat and welding in the new. If you think about that it sounds like a pain. So I think that I am better off replacing the whole piece! from the cats back the exhaust is new... I want more performance with whatever I buy but I am trying to stay away from bolting the stock cats once a year for State inspections.

 

Any Suggestions? I have been looking through jegs and summit but I think that they are over priced and I could find something for a better price with more performance!

 

I want to put the best that I can so let me know what you think!

 

Thanks :D -Economy Builder

dietz4ibanez Senior Enthusiast

dietz4ibanez

Posted
  • Author
Posted

I am going to have to hold off on the cats tomorrow. I think that my front end is going to need some work and it seems to be something with the CV joints. I am going to have it checked out tomorrow! I cant complain this truck has almost 200,000 miles and the only things that have been replaces is the starter, battery or two, heater/ac control unit and thats it... I think that it will ride alot better once its fixed so i cant wait!

dietz4ibanez Senior Enthusiast

dietz4ibanez

Posted
  • Author
Posted
I am going to have to hold off on the cats tomorrow. I think that my front end is going to need some work and it seems to be something with the CV joints. I am going to have it checked out tomorrow! I cant complain this truck has almost 200,000 miles and the only things that have been replaces is the starter, battery or two, heater/ac control unit and thats it... I think that it will ride alot better once its fixed so i cant wait!
  • 1 year later...
tobias Senior Enthusiast

tobias

Posted
Posted
Well I have almost 200,000 miles on my truck and periodically my engine light comes on for catalyst efficiency bank 2. Well I have debated going to auto zone and spending the $70 bucks or whatever cutting out the old cat and welding in the new. If you think about that it sounds like a pain. So I think that I am better off replacing the whole piece! from the cats back the exhaust is new... I want more performance with whatever I buy but I am trying to stay away from bolting the stock cats once a year for State inspections.

 

Any Suggestions? I have been looking through jegs and summit but I think that they are over priced and I could find something for a better price with more performance!

 

I want to put the best that I can so let me know what you think!

 

Thanks :loser: -Economy Builder

 

Man, that's a lot of miles for such a new truck. :dunno:

MS3DALE Senior Enthusiast

MS3DALE

Posted
Posted

Man...An old thread brought back to life!!!!!!

 

BTW Brian....Did you ever get your cats!!! :confused:

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      2 speed transfer case optional now?

      By newdude · Posted

      This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Coastie05
      give me some tips to make my truck look better

      By Coastie05 · Posted

      Go back to OEM wheels. 
    • newdude
      2020 Trailboss 6.2 replacement

      By newdude · Posted

      Probably not their first rodeo, so it should go as planned most likely.  Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together.  We usually put 50-100mi before we hand them back so if something happens, its not after you get it.  A coolant leaks, oil leaks, a ground left off or loose, vibration, etc.     The new engines so far have been good?  There's been a couple that have popped out there again (the replacement engine) but most have been okay.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...