Jump to content

Kylebr1

Member
 View Profile  See their activity

  • Posts

    89

  • Joined

  • Last visited

 Content Type 

Everything posted by Kylebr1

  1. Kylebr1
    One thing i did come across when i was fixing my truck was a shop called TCS transmissions . One guy that worked there had a 2016 sierra 1500 same as mine and had the "shake" . He said there were a couple parts in the transmission (6l80e) that were garbage and that they caused the vibration . He reportedly replaced said parts rebuilt his trans and put in some upgraded parts and there was 0 shake after .
  2. Kylebr1
    Its the fuel pump and is 100 % normal under certain operating temps . 2016 with 120k and no issues here .
  3. Kylebr1
    Axles felt a lot smoother but the shaking was definitely the drive shaft and yes i had a higher quality unit made up. 6" unit 1/4" thick aluminium .
  4. Kylebr1
    Mine was slightly the same way before i did the driveshaft and i think it has to do with rear end and trans temps that being said i have not had the issue since swapping the driveshaft .
  5. Kylebr1
    The factory driveshaft is 1/8" thick i don't think you could machine it at all . The unit i had made is 6" diameter and 1/4" thick .
  6. Kylebr1
    From all the reading i have done i have not seen anyone re-balance there driveshaft and have it fix the vibration the issue is the driveshaft is made of paper thin aluminium and its full of cardboard . Because the driveshaft is so thin it resonates vibrations badly.
  7. Kylebr1
    Sounds like you lost your serpentine belt . Probably went into fail safe mode and shut everything down .
  8. Kylebr1
    Had one made from a company called Pats drive-line I am in Canada so a lot of the american options are to pricey for me . 680$ Canadian i paid . 6" round aluminium one piece unit .
  9. Kylebr1
    This is how mine was when i was fighting to figure out what was causing the vibration . Balanced the wheels got a little better changed the axles got even better then was 100% gone with new driveshaft .
  10. Kylebr1
    What i really mean by all of this is that i think a lot of people say they have a vibration issue because they can see the console move on the highway .. If you had the same truck but with a flow through centre console would you even notice the vibrations ? i know before i had my truck fixed the floor and seats didn't really vibrate more than a normal truck but the lid for the fold down seat always shook like crazy .
  11. Kylebr1
    Yes the big console with no jump seat . I rode in a friends 2016 with the flow through console and it felt a little rough on the highway but not bad and zero centre console shake .
  12. Kylebr1
    I think someone posted a 2017 driveshaft on here and it did look different than the 2016 down models . That being said i dont think i have seen anyone with a flow through centre console have this issue which i find very interesting ..
  13. Kylebr1
    I would ask them to check the run out of the driveshaft and or the rear axle shafts .
  14. Kylebr1
    Just a little update on the truck because i have had a few guys message me and ask . Truck has been very smooth still since changing the driveshaft to a new aluminium one piece and swapping in the Yukon axles . Had my tires road force balanced last week because i lost some wheel weight off-roading and what a difference that has made truck feels smoother now then the day i bought it . Hope this helps others .
  15. Kylebr1
    No mine is good . Center console just shakes on bumpy roads now going to do a center console swap soon .
  16. Kylebr1
    My truck is a 2016 5.3 6 speed . With AFM off . Truck has never gotten better than 14.8 liters per 100 its entire life .
  17. Kylebr1
    I am currently getting 15.8L per 100 with 35s . Very minimal change from factory size . Tires are toyo open country at .
  18. Kylebr1
    No mine is the same way . I think some of the vibration is transmission related . Heat related for sure or Differential heat .
  19. Kylebr1
    15.8L per 100 Truck is lifted 4 " on 35s no gears 5.3 6 speed .
  20. Kylebr1
    No engine work at all .
  21. Kylebr1
    I have 105,000 km now with AFM turned off and have had zero issues .
  22. Kylebr1
    Pretty common , I would advise having your AFM turned off via hp tuners or equivalent.
  23. Kylebr1
    My oversized aluminum driveshaft did fix my vibrations along with a set of yukon axles . However i do find that the center flip up consoles are very shake prone . I would love to know if anyone with a flow through center console has ever complained of "THE SHAKE " .
  24. Kylebr1
    Does it have a electric unit like the vettes then ?
  25. Kylebr1
    I thought i heard somewhere that there were multiple complaints from noises like this on cold start and it was the vacuum pump .

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,800
    Total Members
    8,960
    Most Online
    mans44
    Newest Member
    mans44
    Joined

  • Who's Online   2 Members, 0 Anonymous, 236 Guests (See full list)

×
×
  • Create New...