Jump to content

Body Repair's

jerry67

Recommended Posts

jerry67 Enthusiast

jerry67

Posted
Posted

hi everyone back again with new question, as stated in previous post, redoing my truck, wanted to know if anyone has replaced the rear bed panels on a sportside, (bodyline/driprail area)can i just replace the bed caps or does the whole panel need to be replaced, have not found any easy way to do this without spending a arm&leg on the parts,i'm not in any hurry to do this, but limited time&funds prevent me from woking on truck the way i want to, any idea's or products helpful, thanks jerry67. also anyone with info to bodyshop's in the chicago,il area helpful

59ih340 Enthusiast

59ih340

Posted
Posted
hi everyone back again with new question, as stated in previous post, redoing my truck, wanted to know if anyone has replaced the rear bed panels on a sportside, (bodyline/driprail area)can i just replace the bed caps or does the whole panel need to be replaced, have not found any easy way to do this without spending a arm&leg on the parts,i'm not in any hurry to do this, but limited time&funds prevent me from woking on truck the way i want to, any idea's or products helpful, thanks jerry67. also anyone with info to bodyshop's in the chicago,il area helpful

It's cheaper,faster and easier to get a good used bed.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • GN2018
      Range AFM/DFM Disabler Flaw

      By GN2018 · Posted

      Actually, it probably was the brakes.  It's weird the way the messages came across, but I took it to the dealer thinking that something was wrong with the sensor and in fact, the rear brakes were shot.  What I don't understand is why the messages never said, your brake pads are low.  First I got the message I posted above, taking about new pads being detected.  Then I got a message saying that the system needed repaired.  It never said, change your brake pads.
    • No1UKnow
      Transmission Woes :-(

      By No1UKnow · Posted

    • ryan35205
      Lets Talk Z60 Suspension

      By ryan35205 · Posted

      Did the KYBs keep it the same height in the front? I was concerned that pre-assembled assembly would raise it up an inch to standard non-z60 height.. I guess which it would make the rake 1 inch instead of 2 inches.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Thank you for keeping the train on the tracks and for a thoughtful engagement. I enjoyed the reflection on a previous stance to refine and improve your position. I like that inquisitive flexibility about you Atlas.    No the process isn't sterile. Hundreds, perhaps thousands of miles of piping, vessels, pumps. Chevron, the people I worked for, were keenly aware that there is a market for what is known as their "ISOCLEAN" line of lubricants. These are lubricants that are the same as those sold bulk that are further processed by filtration to a level your particular application demands. They will filter and package and provide lab documentation as required. Do not kid yourself. Every gallon of oil that goes into a Chevron Turbine, reciprocating compressor, generator is prefiltered and tested before being charged. Lest wise it was when I was there in the plants I worked in.    There are requirements set by manufactures for the cleanliness of the oils used in their equipment. OTR such as CUMMINS has standards shared with customers on this. Commercial interest selling to Ma and Pa do, but don't share that information. Not even upon request but internally, they do exist.    The GM study sited, (Graph from Machinery Lubrication in previous post) only shows "relative" importance.  I find that fascinating. By constructing the graph like this they admit there are dozens of factors in engine life and via scientific method determined the effect of 'relative cleanliness' on engine life not in miles but in 'FACTORS'. This allows a certain amount of reverse engineering does it not?   They even provided some touchstones. Beta 75 as a reference point. Wonderful stuff!!   Smaller blenders CAN and some DO take the time and effort to do better than a refinery or large bulk blender, like Warren Oil, in improving the "in the can" cleanliness. No I don't have a list but testing could generate that information.    Again, but one of several levers we can pull to improve engine life. The simplest is keeping a clean work station while doing your own oil changes.     
    • Mykel544
      New Guy from Oklahoma

      By Mykel544 · Posted

      Thank you. I'll give it a try 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...