Jump to content

Leveling Kit With Spacer Instead Of 5100's

slimcubby

Recommended Posts

slimcubby Enthusiast

slimcubby

Posted
Posted

I see a LOT of people using the CCM 2.5" leveling kits on the NNBS and it is making me rethink going with the 5100's which only barely get 1.7" of lift in the front. I searched a lot and only really see threads on what leveling kit they are using and not really the pros/cons. Are there any disadvantages or problems with spacers? I always thought that they were bad because they are extending the stock strut making everything have harsh angles thus going 5100 safer since it preloads the stock spring. If anyone can help me with some information on the spacers I would appreciate it.

oldschool327 Senior Enthusiast

oldschool327

Posted
Posted

BILSTEIN............ Nuff said!

 

I was looking for a better off road ride not just a lift, that was my reason for the 5100's.

 

I am getting ready to throw the spacers back in and use the Bilsteins on the 2nd lowest notch to offset my planned Fab Fours front bumper wieght this spring.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • haoleboyZ71
      Radio Update

      By haoleboyZ71 · Posted

      Hi, New here.  2026 Denali HD.  Just purchased 7/2/26. I am having the same issue.  I just traded in my 2024 AT4, and the truck connected to bluetooth and Android Auto Immediately!  Now, with the new HD, it connects when it wants to, which is usually not at all.  I have to use the usb-c cable to get it to connect.  Bluetooth won't even connect without the AA. Now after saying all that, I'll take a 20 min drive with the phone plugged in.  Stop at a store, restaurant, etc....  Get back in my truck and DO NOT plug the phone in.  The truck then decides at this point, lets connect BT & AA and work perfectly, ie how it should.   I have deleted (forget phone) the phone multiple times.  I guess I'll just get used to plugging it in every time. even though I don't think its good for the phone battery to have it on charge after it hits 100%. I have searched all over.  No one else seemed to be having this issue, until I read this thread today.   thanks for reading.
    • Heath
      2004 GMC Sierra Crew Cab Ignition issues

      By Heath · Posted

      I have an issue with my ignition hanging and I have to tilt the steering wheel to get in the off position. I have used a great key lock spray and it doesn't help resolve the issue. Is this an ignition assembly issue or something else. If anyone has a past experience with this please advise.   Thanks  Heath
    • jl6690506
      Bent valve in 2025 GMC Canyon Denali - Requires engine swap at 14K miles

      By jl6690506 · Posted

      This is a terrible GM warranty experience, two months waiting for a covered engine swap with no loaner or timeline is not allowed under GM’s courtesy transport policy.Escalate straight past regular support to a GM executive case manager, document every closed service ticket and dealer repair paperwork. File a complaint with NHTSA to force faster action, and ask for daily rental reimbursement while your truck is down. If it’s been out of service over 30 days, your state lemon law may let you pursue a full vehicle buyback.
    • jl6690506
      2019 GMC Sierra 1500 - 8l90

      By jl6690506 · Posted

      198°F isn't unusually hot for an 8L90, so I don't think temperature alone caused the issue. Since everything returned to normal after the truck sat for several days, I'd be looking at an intermittent electronic or hydraulic control problem before assuming the transmission itself has failed. The first thing I'd do is scan the Transmission Control Module (TCM), not just the ECM. GM transmissions can store manufacturer-specific or history codes that won't trigger a check engine light. I'd check: TCM history and pending DTCs Commanded vs. actual gear Line pressure Shift solenoid status Torque converter clutch (TCC) slip Transmission fluid temperature If it happens again, try to capture the data before cycling the ignition, since some intermittent faults disappear after a restart. A professional scan tool that supports full GM transmission diagnostics makes this much easier. For example, the Foxwell NT809BT can access the TCM, read manufacturer-specific transmission codes, and display live transmission data that's not available on a basic OBD-II reader: https://www.foxwelldiag.com/products/foxwell-nt809bt Hopefully it's just an intermittent control issue, but I'd definitely pull the TCM data before replacing any parts.
    • jl6690506
      2019 GMC Sierra 1500 - 8l90

      By jl6690506 · Posted

      Sorry, I accidentally posted in the wrong language. I'll repost it in English.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...