1994 Chevy S10 P/u 2.2 L 4 Cylinder

By smams1962
January 26, 2011 in Gen III & Gen IV V8 Engines (LS-Based)

Recommended Posts

smams1962

Posted January 26, 2011

I attempted to replace starter with access problems. It appears that I may have to remove flywheel/bell housing cover & also need to access from driver wheel well. Please respond with any help.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.4k
Total Topics

2.7m
Total Posts
Member Statistics

342,754
Total Members

8,960
Most Online

Newest Member
scotthvac.net
Joined 3 hours ago
Who's Online 1 Member, 0 Anonymous, 477 Guests (See full list)
- Disabled Mike

Latest Articles
- Next-Gen 2027 GMC Sierra 1500 Revealed: Gen-6 V8s, Motorized Displays, and a Major Trim Shake-Up
  17 hours ago
- 1996 Chevy Blazer vs 2026 Blazer: Epic Head-to-Head Crash
  Wednesday at 07:57 PM
- Chevy Revives Iconic “Heartbeat of America” Campaign
  Wednesday at 02:54 PM
- 2027 Chevrolet Silverado: Every Official Photo
  June 18
Posts
- Question about torque specs and possible reason for noise
  
  By davester · Posted 2 hours ago
  
  alldata.com will have the torque specs for all those bolts.
- loose lug nuts
  
  By davester · Posted 2 hours ago
  
  maybe make sure both the hub and the rim surfaces are flat and corrosion free? I know for both my '04 and '12 3500, which are both duallies, I've had the rear wheel lugs loosen sometimes, after tightening, then driving a bit and then re-torquing them. The fronts also sometimes, but much less common vs the rears. And if you have the flanged flat face (vs the acorn style) lug nuts, make sure the flange part can spin easily. I spray some fluid film on the outside and work it into the groove until the flange can spin easily, making sure not to get FF on the threads. This seems to have helped with the lugs getting properly torqued, so they stay tight.
- 2024 2500HD LTZ front end swap to LT
  
  By scotthvac.net · Posted 3 hours ago
  
  Did you need to buy any of the mounting brackets? I spent hours looking for the front facia figures I found it then I joined this forum.. but I’m ordering the upper cover facia now do I need bolts screws nuts ? Anything else?
- 2022-24 halogen - led grille swap
  
  By scotthvac.net · Posted 3 hours ago
  
  So I’m looking to swap my 2022 halogen to 2024 led 2500 hd front. I have the grill the headlights - halogen to led 8 to 12 pin wiring harness. I just found the front bumper upper cover facia and I’m looking to see if anyone has a parts list to help me out with. I’m going to need the mounting brackets to install the grill and headlights. I’ve been on some gm parts sites and it’s just horrible trying to figure it out.
- 2027 GMC Sierra: Official Discussion
  
  By Jsdirt · Posted 3 hours ago
  
  Another massive smartphone in the dash! I guess one wasn't enough. Just what I want. 🙄 At this stage GM would have to pay ME to drive anything they've built the past 20 model years. Once was enough for me. Learned my lesson.
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 156 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  Atlas
  19
2. 2
  
  Chuck FB
  12
3. 3
  
  newdude
  9
4. 4
  
  KARNUT
  9
5. 5
  
  Z45
  5
Show More