Selectable Ride Shock Extensions

By okc666
June 24, 2011 in Advanced Drivetrain, Suspension & Tuning

Recommended Posts

okc666

Posted June 24, 2011

hi all, i was hoping somebody/s might have some information on where i could locate shock extensions for selectable ride shocks. it seems they are more rare than i thought. i need a about a 1 inch extension. ive been to a few shops out here and they dont seem to know of anything available, but then again they never really looked. they just said no. the dealership isnt much help either but they did say if i disconnect them to run aftermarket shocks ill get a trouble code, so any resources or helpful tips would be greatly appreciated, thank you.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.3k
Total Topics

2.7m
Total Posts
Member Statistics

342,714
Total Members

8,960
Most Online

Newest Member
Peoplemvr
Joined 1 hour ago
Who's Online 12 Members, 1 Anonymous, 765 Guests (See full list)
- Peoplemvr
- 4RNER
- mdipasquale20
- OnTheReel
- PhilB
- KARNUT
- revmanii
- Snow White
- ksiesel
- rusty503
- PunchT37
- thedevdavid

Latest Articles
Posts
- GMC 1500 Illuminated Front Grill Emblem REPLACEMENT.
  
  By Peoplemvr · Posted 1 hour ago
  
  Hi there. Long time lurker, first post. i have read the previous posts regarding the water ingress problem with this emblem. I bought my 1500 SLT the summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways. As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem. And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE. Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash to keep the salt off. Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo. But there was plenty of water inside when I ripped it apart. Prior to installing the new assembly I tried it with the old harness and it works fine. Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe. I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it. If this one fails, I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL. Any thoughts on sealing with epoxy would be appreciated. Thx! Doug
- Looking at ordering a '26 WT because I want a std cab, std bed
  
  By revmanii · Posted 2 hours ago
  
  PS: Here's pic of the 2014 wheels I'd like to run when it's not winter. Stuck my finger around new wheel caliper setup. Very little clearance. I suspect these won't fit, but won't know for sure till I try. Edit: And my first mod. Stubby antenna from the old truck.
- Looking at ordering a '26 WT because I want a std cab, std bed
  
  By revmanii · Posted 2 hours ago
  
  I bought it today and brought it home. They still owe me the bed liner, remote start, and they also agreed to get me the flat black bumpers to replace the optional chromes ones. While some folks may think I'm crazy, I think they'll look a lot better with all the other black stuff. Blacked out grill, mirrors, running boards, dark essentials Chevy tailgate lettering along with the black Silverado and Turbomax emblems. I do want replace dark essentials Chevy front grill emblem with the base level gold one. The 2.7 4 seems to run well and push a 1500 along just fine :).
- Gas Prices
  
  By Grumpy Bear · Posted 2 hours ago
  
  One of the most useful post I've seen. Thank you.
- Gas Prices
  
  By Atlas · Posted 4 hours ago
  
  Conversations with a hickory stump be like:
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 156 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  KARNUT
  19
2. 2
  
  Grumpy Bear
  18
3. 3
  
  Chuck FB
  11
4. 4
  
  Atlas
  9
5. 5
  
  Black02Silverado
  8
Show More