Weird sounds after leveling.

By Sublime69
November 16, 2014 in 1999-2013 Silverado 1500 & Sierra 1500

Recommended Posts

Sublime69

Posted November 16, 2014

2004 silverado regular cab short bed. I just installed a RC leveling kit. After I installed it I now have this very strange clicking/squeaking sound that sounds like it's coming from the drivers side behind the cab. It only happens when I accelerate hard. If I take off normally it doesn't make any noise. I think I heard this sound very rarely before I did the leveling. I checked driveshaft and I did notice a little play up and down where the shaft goes into the t-case. Any thoughts?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.4k
Total Topics

2.7m
Total Posts
Member Statistics

342,840
Total Members

8,960
Most Online

Newest Member
appletrav
Joined 7 hours ago
Who's Online 9 Members, 0 Anonymous, 423 Guests (See full list)
- mikeyk101
- Chevrolet1
- CamGTP
- Vegas22
- KARNUT
- PunchT37
- SoCal Angler
- stanz792
- 03blackz71

Latest Articles
- Hummer Turns 25 and GMC Brought the H2’s Yellow Back
  Wednesday at 06:04 PM
- What’s New for the 2027 GMC Yukon and Yukon XL
  July 13
- Got a “Service Door Latch” Alert? Fix It in a Minute
  July 9
- GM Recalls Cadillac VISTIQ Over Power-Folding Seats
  July 8
Posts
- 2020 Trailboss 6.2 replacement
  
  By newdude · Posted 46 minutes ago
  
  Probably not their first rodeo, so it should go as planned most likely. Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together. We usually put 50-100mi before we hand them back so if something happens, its not after you get it. A coolant leaks, oil leaks, a ground left off or loose, vibration, etc. The new engines so far have been good? There's been a couple that have popped out there again (the replacement engine) but most have been okay.
- Different requirements for oil filters?
  
  By CamGTP · Posted 1 hour ago
  
  To me it honestly makes zero difference what filter you run. It's not a race engine, just a truck engine that's mostly bumming highways and it just needs a filter that filters oil. The filter used to be a 7060 and the long version was a 7045. Now it's the newer updated filter that the K2XX trucks and newer run, the 100255 I believe if we are using napa numbers. Any of those filters is going to do the job. I wouldn't overthink it, to me it makes no difference because those first filter numbers worked for 18+ years before the spec suddenly changed.
- No 12v outlets in 2026 gmc Sierra
  
  By cautious optimist · Posted 3 hours ago
  
  My phone (OnePlus) requires a proprietary charger to get the full 80w fast charging benefits. The only option to get these fast charging benefits is a 12v plug. Any other charger and my phone defaults to 25w charging. I also have a tire inflator with a back up 12v plug. USB would never keep that thing going in a pinch. Putting just one in the trucks wouldn't hurt. Good laptops still include at least 1 USB-a port.
- Chirping/squeaking coming from under dash when driving over bumps
  
  By appletrav · Posted 6 hours ago
  
  2017 Sierra 1500 SLT I read that there’s a bolt on the battery brace that sometimes gets loose. I checked all the bolts around there that I could, and all were tight. This sounds more like it’s under the dash, maybe closer to the driver footwell. Anyone else have this problem, or know a possible cause? https://imgur.com/a/kaQRZZH
- Different requirements for oil filters?
  
  By glenn27 · Posted 10 hours ago
  
  Morning here- I have a 2013 GMC Sierra 1500-5.3 L engine (low mileage -two owner)--I'm retired now-so I don't drive as much--anyway-just had the oil /filter changed-I have always used Amsoil Synthetic and NAPA gold oil (#7045) filters-now i read that GM has changed the oil filter requirments for these engines- and they (GM) recommends/ want to go w/ a different filter w/ more psi rating on the relief valve (in the filter) to open like 22 psi. The above featured one I mentioned shows 12-15 PSI--which doesn't kmeet these new specs.. Wow-stuff is like getting more/more technical all the time. I think it looks like trying to avoid these sticky lifter problems. Any thoughts or recommendations here? I'm kinda confused-- Thank you- glenn
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 157 members
- diesel 3.0
  
  Open Club · 281 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 213 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  Grumpy Bear
  19
2. 2
  
  Chuck FB
  17
3. 3
  
  newdude
  13
4. 4
  
  txab
  10
5. 5
  
  KARNUT
  8
Show More