Jump to content

Slightly used Magnaflow Muffler 3/3 5x18


Recommended Posts

Posted

A little to loud for my taste (read: too loud for the wife ).eusa_doh.gif

 

This is a Magnaflow, wide open, aluminized muffler p/n 12289 (5x8x18). This has 3" inlet/outlet and dual 3" inlets/outlets. Magnaflows are reversible so take your choice.

I currently have it as a 3" in and dual 3" outs to the stock "Y" pipe and then out the stock 3" tailpipe. Have already ordered a 12579 (3" in/3" out, 22" long) to calm her down a bit.

It gives a very good growl on acceleration and a slight gurgle at idle. Pretty silent at 60 mph but you will hear it under load and at startup. Got this off Ebay ($85, NIB) and have put about 500 miles on it. Will have it available to ship by Fri (5/13). Looking for $65 shipped to the lower 48. My loss - your gain.

 

Will take paypal (credit card or echeck) or will ship upon clearance of your personal check.

 

Thanks!

 

 

 

281sa.gif

  • 3 months later...
Posted
A little to loud for my taste (read: too loud for the wife ).

 

This is a Magnaflow, wide open, aluminized muffler p/n 12289 (5x8x18). This has 3" inlet/outlet and dual 3" inlets/outlets. Magnaflows are reversible so take your choice.

I currently have it as a 3" in and dual 3" outs to the stock "Y" pipe and then out the stock 3" tailpipe. Have already ordered a 12579 (3" in/3" out, 22" long) to calm her down a bit.

It gives a very good growl on acceleration and a slight gurgle at idle. Pretty silent at 60 mph but you will hear it under load and at startup. Got this off Ebay ($85, NIB) and have put about 500 miles on it. Will have it available to ship by Fri (5/13). Looking for $65 shipped to the lower 48. My loss - your gain.

 

Will take paypal (credit card or echeck) or will ship upon clearance of your personal check.

 

Thanks!

 

Do you still have the set up available? Can it be shipped to North Pole, Alaska 99702 or Fairbanks, Alaska? If so, will it fit a 2002 GMC Sierra 1500 reg cab 2wd with a 5.3L?

Posted
A little to loud for my taste (read: too loud for the wife ).

 

This is a Magnaflow, wide open, aluminized muffler p/n 12289 (5x8x18). This has 3" inlet/outlet and dual 3" inlets/outlets. Magnaflows are reversible so take your choice.

I currently have it as a 3" in and dual 3" outs to the stock "Y" pipe and then out the stock 3" tailpipe. Have already ordered a 12579 (3" in/3" out, 22" long) to calm her down a bit.

It gives a very good growl on acceleration and a slight gurgle at idle. Pretty silent at 60 mph but you will hear it under load and at startup. Got this off Ebay ($85, NIB) and have put about 500 miles on it. Will have it available to ship by Fri (5/13). Looking for $65 shipped to the lower 48. My loss - your gain.

 

Will take paypal (credit card or echeck) or will ship upon clearance of your personal check.

 

Thanks!

 

Do you still have the set up available? Can it be shipped to North Pole, Alaska 99702 or Fairbanks, Alaska? If so, will it fit a 2002 GMC Sierra 1500 reg cab 2wd with a 5.3L?

 

 

 

 

 

 

Howdy, WT! North Pole???? Cool (or cold)!!

Anyway, still have it, was actually going to ebay-it this weekend. Checked on shipping to your Zip and it would run around $30 big ones (not exactly sure of weight and dim's yet). I would sell it to you for $75 shipped. It really only has about 500 miles on it. I assume it would fit your '02 w/5.3L. You might wanna check to be sure, tho. I have the stock avlanche "y" still on the dual outlets, so if you are planning on running duals out the rear, I could cut the "y" pipe off and save on packaging. Just let me know.

 

Thanks, Mike.

Posted

Yep North Pole. Its not too cold yet but it is starting to cool down lately. I'm active duty Air Force stationed up here in Alaska. Just got here in june, so far I really like it. Lots of hunting and fishing to do. Your offer sounds great, and i planned on leaving the exhaust set up as is. That is the side exit I mean. Unless it is not too difficult to put the duals out the back like you mentioned? Anyway I will take the whole set up you have. I will have to wait till payday which is the 1st of September. Us military folks only have money twice a month the 1st and 15th (lol). So, I hope you agree with this if not just shoot me a message and let me know.

Posted
A little to loud for my taste (read: too loud for the wife ).

 

This is a Magnaflow, wide open, aluminized muffler p/n 12289 (5x8x18). This has 3" inlet/outlet and dual 3" inlets/outlets. Magnaflows are reversible so take your choice.

I currently have it as a 3" in and dual 3" outs to the stock "Y" pipe and then out the stock 3" tailpipe. Have already ordered a 12579 (3" in/3" out, 22" long) to calm her down a bit.

It gives a very good growl on acceleration and a slight gurgle at idle. Pretty silent at 60 mph but you will hear it under load and at startup. Got this off Ebay ($85, NIB) and have put about 500 miles on it. Will have it available to ship by Fri (5/13). Looking for $65 shipped to the lower 48. My loss - your gain.

 

Will take paypal (credit card or echeck) or will ship upon clearance of your personal check.

 

Thanks!

 

 

 

Do you still have the set up available? Can it be shipped to North Pole, Alaska 99702 or Fairbanks, Alaska? If so, will it fit a 2002 GMC Sierra 1500 reg cab 2wd with a 5.3L?

 

 

 

 

 

 

Howdy, WT! North Pole???? Cool (or cold)!!

Anyway, still have it, was actually going to ebay-it this weekend. Checked on shipping to your Zip and it would run around $30 big ones (not exactly sure of weight and dim's yet). I would sell it to you for $75 shipped. It really only has about 500 miles on it. I assume it would fit your '02 w/5.3L. You might wanna check to be sure, tho. I have the stock avlanche "y" still on the dual outlets, so if you are planning on running duals out the rear, I could cut the "y" pipe off and save on packaging. Just let me know.

 

Thanks, Mike.

 

 

 

 

 

Personally I would probably just go with the one side exit and put a nice tip on'er. I will leave the "y" on so you can go either way with it. Sept is cool, I will be out of touch from about sept 1 thru 4. My paypal addy is "[email protected]".

I am on ebay under "melbert4" so you can check my feedback there. I have also sold on this site to a few folks, email me if you need references. So, I'll holler back at you come Sept 4 or 5 and we can go from there? thanks, Mike.

  • 2 weeks later...
Posted
A little to loud for my taste (read: too loud for the wife ).

 

This is a Magnaflow, wide open, aluminized muffler p/n 12289 (5x8x18). This has 3" inlet/outlet and dual 3" inlets/outlets. Magnaflows are reversible so take your choice.

I currently have it as a 3" in and dual 3" outs to the stock "Y" pipe and then out the stock 3" tailpipe. Have already ordered a 12579 (3" in/3" out, 22" long) to calm her down a bit.

It gives a very good growl on acceleration and a slight gurgle at idle. Pretty silent at 60 mph but you will hear it under load and at startup. Got this off Ebay ($85, NIB) and have put about 500 miles on it. Will have it available to ship by Fri (5/13). Looking for $65 shipped to the lower 48. My loss - your gain.

 

Will take paypal (credit card or echeck) or will ship upon clearance of your personal check.

 

Thanks!

 

 

 

Do you still have the set up available? Can it be shipped to North Pole, Alaska 99702 or Fairbanks, Alaska? If so, will it fit a 2002 GMC Sierra 1500 reg cab 2wd with a 5.3L?

 

 

 

 

 

 

Howdy, WT! North Pole???? Cool (or cold)!!

Anyway, still have it, was actually going to ebay-it this weekend. Checked on shipping to your Zip and it would run around $30 big ones (not exactly sure of weight and dim's yet). I would sell it to you for $75 shipped. It really only has about 500 miles on it. I assume it would fit your '02 w/5.3L. You might wanna check to be sure, tho. I have the stock avlanche "y" still on the dual outlets, so if you are planning on running duals out the rear, I could cut the "y" pipe off and save on packaging. Just let me know.

 

Thanks, Mike.

 

 

 

 

 

Personally I would probably just go with the one side exit and put a nice tip on'er. I will leave the "y" on so you can go either way with it. Sept is cool, I will be out of touch from about sept 1 thru 4. My paypal addy is "[email protected]".

I am on ebay under "melbert4" so you can check my feedback there. I have also sold on this site to a few folks, email me if you need references. So, I'll holler back at you come Sept 4 or 5 and we can go from there? thanks, Mike.

 

 

 

 

 

PM sent your way.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,863
    Total Members
    8,960
    Most Online
    Bulldogger
    Newest Member
    Bulldogger
    Joined
  • Who's Online   4 Members, 0 Anonymous, 847 Guests (See full list)

  • Latest Articles

  • Posts

    • Around 2008 if memory serves they took sulfur out. That was when diesel went up. 
    • Question for you Grumpy, why is diesel so much more than gasoline? Seems to me that it may be slightly a little less refined than gas and it doesn't have 10% alcohol which presumably lowers the price of gas
    • Thanks, so being a different beast altogether, anyone know what the "optimal" temp is for the 10L80/90 for proper shifting?
    • How many years have I pointed out every point in that link to the folks here and been avalanched with criticisms and outright hostilities at times? I ran counter to even the great CUSTOMBOSS and Lake Speed Jr and the half dozen experts on YouTube and in the final.....GM, Physics (Stribeck) backs that Grumpy old Bear.    Honestly, I never said a thing engineering hadn't studied silly and laid in concrete during WWII. But I'm old, the information is old and yet, the Laws of Physics are eternal.    Okay there is one exception. I vehemently disagree with their use of the word 'tolerances' when what it meant is "clearance".   The clearance is the distance between two objects. The tolerance is the degree of acceptable variation permitted in that clearance. I.E., piston to bore clearance is 0.004" with a tolerance of +/- .0002" so the clearance is in specification if it lies between 0.0038" and 0.0042". Cutting that 'tolerance in half has ZERO impact on lubrication requirements. Makes for more difficulty in manufacturing.  But a tighter clearance 'MAY'. Depends on finish. Anyway....   It's one of those statements made by people to make themselves look smarter than they are to convince people who are as un-enlighten as they seem to manipulate their behaviors. But hey, the blind leading the blind puts them both in the pit. 
    • Out and about yesterday on a long Saturday drive I passed a lot of Shell stations. My preferred, so I pay attention. Lot's of small town Illinois so not six stations in three blocks like the city.    Everyone of them over a radius of say 100 miles had regular at $4.19 but one which was the one closest to home at $4.15. However Premium pricing varied greatly between 85 cents over regular to $1.50 over. I'm not counting the price of the station with the lowest regular so the reference is the same for the remainder and all within the same brand. However the spread discrepancy holds across all brands.     @txab, any thoughts on that? 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...