Jump to content

Fog Light Wiring causing 'ding ding ding'

dklumph

By dklumph
in Ask A GM Technician

Recommended Posts

dklumph Enthusiast

dklumph

Posted
Posted

I recently added a set of PIAA 520 fogs and followed the manufacturer's wiring instructions and used their supplied harness & switch. The lights are tied to the driver's side low beam (yellow wire). The lights function properly only when low beams are on but since installing them when I press the electic door lock button when exiting the truck I get a 'ding ding ding' warning bell. If I immediately hit the door lock again it will lock. It's as if there some kind of feed back or something. I suppose I can get used to it but would like to find out the cause and eliminate the annoyance.

 

Thanks!

 

Don

ryank1 Enthusiast

ryank1

Posted
Posted

You have enabled the delayed locking feature on your truck. In your owners manual it will tell you how to disable it.

dklumph Enthusiast

dklumph

Posted
  • Author
Posted
You have enabled the delayed locking feature on your truck. In your owners manual it will tell you how to disable it.

 

 

Thanks Ryan! Last night it occurred to me that something might be related to that. I've always had the doors lock when I put it in Drive and unlock when in Park. I'll check today to see if the doors are on an actual timed delay rather than my previous preference of 'D' & 'P'. I wonder if having the negative battery term. disconnected for awhile for the install would have reset my preferences.

 

Thanks again. I'll report back later today if that resolved the issue.

 

Don

dklumph Enthusiast

dklumph

Posted
  • Author
Posted

Ryan, you're da' man! The delay lock was on. Turned it off and that warning chime is gone now when I lock my doors when exiting the vehicle!

 

Thank you!

 

This board is great!

 

Don

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   3 Members, 0 Anonymous, 1,375 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed, regardless of whether they are in warranty or not, or in the hands of the original owner or not. Why not updates as well, especially since some of those can be safety related also?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...