Jump to content

Need Help Picking Exhaust


Recommended Posts

Posted

Hey guys im a new member and i was wondering if i could get some feedback on what i should do as far as an exhaust for my truck. I have an 06 GMC 1500 4.8L and i want an exhaust that will give me a better sound, but i dont want to spend a fortune. I was thinking about running a cat back system out the side infront of my tires with a Glasspack exhaust. I dont know if this is good or not. Please help me out, all suggestions are helpful, tell me what you think. I really want it sound deep and good.

Thanks

Gunn

Posted

I personally would not use a glasspack.. If I were you id look at Magnaflow or Borla catback.. Both of those arent too expensive and will give you a unique sound plus a little power..

Posted
Hey guys im a new member and i was wondering if i could get some feedback on what i should do as far as an exhaust for my truck. I have an 06 GMC 1500 4.8L and i want an exhaust that will give me a better sound, but i dont want to spend a fortune. I was thinking about running a cat back system out the side infront of my tires with a Glasspack exhaust. I dont know if this is good or not. Please help me out, all suggestions are helpful, tell me what you think. I really want it sound deep and good.

Thanks

Gunn

 

 

I've always been a flowmaster guy. Here's my '00 4.8L, with a SI/DO Flowmaster Original 40.

 

 

Posted

I have a dual Magnaflow set-up on my 6.0. The mufflers are preety cheap for a good quality part. I have a custom exhaust from the cats back. I wanted it out the side after the rear tires and run two mufflers. I have had other mufflers in the past, and the Mangaflow wins hands down. Little more power, nice sound when you are on it, but crusin it is nice and quiet in the cab. My vote is Magnaflow.

Posted

Might I suggest true duals, nothing like the sound of duals.

 

 

 

2.5" is the thickest I would go on duals for the 4.8, and I would say go with the Super 44 Flowmasters, but if you want not so loud & a quality built muffler go with Magnaflow.

  • 2 weeks later...
Posted

If you don't want it real loud, look into something like I've got. Kept the stock pipes and had a large Magnaflow put in. Sounds like stock at idle inside the truck, but you can hear it when you give it gas though it's not so loud in the truck that you have to turn up the radio to hear it. I'll try to get some sound clips of it and post them, just haven't gotten around to it yet.

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • I like things to be more nailed down. For instance. People ask why my father left a multi million dollar business in NJ in the seventies and started over in Texas. The answer is simple, payola, threats and quality of life. He didn’t like the game. And he didn’t want his kids to be wrapped up in that mess. That’s nailed down no guessing. 
    • So any kind of deviation is not permitted. Even if it manages to touch on Oils Chain intervals only if, it addresses your latest threat. Boring.😴 
    • The tailgate of pickups is not designed to be water tight. There are seal kits for them but I doubt they work effectively. But, I've not tried them. I always have hard folding tonneau covers and the BakFlip brand has been my favorite. And, for the most part, the bed stays dry. I would invest in some bins that can be closed to better protect sensitive stuff. 
    • A properly installed tonneau will keep out 95% of the water.  As others have said, the only way to be completely dry is to either get a topper or an SUV.   I've run virtually all the trifolds and hard rolling that are out there.  My thoughts:   1.)  The leak points of any cover will be the front corners, and around the tailgate.   They will also leak if the rails are not installed properly.  If you take a electric/cordless ratchet and snug down the clamps, you run the risk of overtightening which causes the rails to sag.  When the rails sag it creates a gap between the rail and the bed cap and this lets water in.   2.)  Different manufacturers use different methods to try and seal the front.  The "driest" setup is probably the Leer HF650M, which uses double seals all the way around and doesn't require a foam seal across the front edge of the bed.  The Realtruck trifold covers (Bak, Undercover, Gator, etc...) all use a foam seal across the front, and drain tubes.   3.)  Realtruck has standardized the way that the cover attaches to the rail.  With the exception of the Extang Endure ALX, all other Realtruck covers use a plastic clamp which slides into a channel, hooks onto the edge of the rail, and tightens down. The "Realtruck Advantage" covers sold by GM dealers as an OEM accessory still use the "bolt through the panel" installation method.  Problem with these is over time, water gets past the rubber seal, into the panel, and once they become waterlogged they begin to delaminate (and weigh a ton.)   4.)  Unless you are using GM Rewards points, buy your cover separately.  Realtruck offers a 5 year warranty on BAK, Undercover and Extang covers.  Gators get either a 2 or 3 year warranty.  If you have an issue, they are much easier to deal with.  If you have an issue with an OEM GM cover, you have to go through the service department and GM Warranty processes to get it taken care of.   Recommendations based on my experience:   Hard folding:   1.)  Undercover Ultra/Armor Flex (identical except Ultra has carpet on the underside and a smooth finish.  Armor has no carpet but has a Line-X coating on the outside.) 2.)  Leer HF650M.  Has 4 panels instead of 3.  Double seals to keep the water out.  Downside is only a 3 year warranty and warranty only honored if you purchase from a Leer dealer.  If you have your dealer install it or buy off Amazon they won't warranty it. 3.)  Bak MX4.  They sell a ton of them.  A good cover for the money when you can find one on sale.  About to be redesigned to include a spring to ease opening and closing. (Supposed to be released 7/26.  Bak MX4 EZ-Lift)   Hard rolling:   Bak Revolver X4S or X4TS (has t-slot rails.)  Personal favorite and the one I use on my truck.  Easy to roll up one handed.  Doesn't block the rear window.  Only costs you about 6" of the bed when open as opposed to a retractable canister which eats up about a foot of bedspace.  Downside is it's either all the way open or all the way closed.   Good luck with you search.    
    • Does any of this change if the seller dropped the price to $22.5k?  Mechanic is supposed to verify the transmission concern but they have not got back to me yet.  Even if a transmission needed to be purchased, I'm looking at <$30k which puts me right back to where I started.   In the meantime, I test drove 2 trucks locally back-to-back, one Denali and one SLE, the SLE was noisy, jerky, and did not inspire confidence, while the Denali was over $30k but just sold the other day.  If $32k buys you a Denali with 100k miles and this truck can be had for $32k with a brand new transmission, with GM parts warranty, does that skew things?   FWIW, all the trucks I drove locally had a much worse service history - emissions work, valve body work, one even had the whole transmission replaced with lower mileage than the one in TX.  I'm guessing those were "short trip" vehicles, as they only racked up around 100k miles in 6 years - a lot less than 164k miles in just under 6 years.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...